Whirlpool RBD245PDT Use and Care Guide - Page 19
li tA.acment, IC,e°, o,erot,o.
View all Whirlpool RBD245PDT manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 19 highlights
iiiiiEi!i'ectcriocnan' ection junction cable from power supply box _ red_ junction cable from power supply Electrical Shock Hazard Disconnect power to the junction box before making connection. Electrically ground oven. Connect ground with 10-gauge-minimum solid copper wire. Failure to follow these instructions could result in death, fire or electrical shock. This oven is manufactured with white (neutral) power supply wire and a cabinet-connected bare grounding wire twisted together. • Ftheeedcaobviennet.caMbaleketheroleucgthricaolpceonninngecitnion following the steps needed for your installation. 1. Disconnect the power supply. 2. Remove the junction box cover. 3. Connect oven cable to junction box through the U.L.-listed conduit connector. 4. Connect the two black wires together with twist-on connectors. 5. Connect the two red wires together with twist-on connectors. 6. Complete electrical connection according to local codes and ordinances. white _ w_re _ grounding oven cable wires -factory crimped Figure 1 cable from oven conduit connector If local codes PERMIT connecting cabinet-grounding conductor to neutral white wire in junction box: 7. Connect the factory-crimped bare and white oven cable wires to the neutral (white) wire in junction box. See Figure 1. 8. Replace junction box cover. Figure 2 cable from oven connector If local codes DO NOT PERMIT connecting cabinet-grounding conductor to neutral white wire in junction box: 7. Separate the factory-crimped bare and white oven cable wires. 8. Connect white oven cable wire to neutral (white) wire in junction box. See Figure 2. 9. Connect the bare grounding oven cable wire to a grounded wire in the junction box. See Figure 2. 10. Replace junction box cover. If connecting to a four-wire electrical system: 7. Separate bare and white oven cable wires. 8. Connect white oven cable wire to neutral (white) wire in junction box. See Figure 2. 9. Connect the bare grounding oven cable wire to the green grounding wire in junction box. Do Not connect bare grounding wire to neutral (white) wire in junction box. See Figure 2. 10. Replace junction box cover. li tA.ac"ment Carefully push against seal area of oven front frame when pushing oven into cabinet. Do Not push against outside edges. 0 - 8 • Replace oven racks. 4 screws Irmatpinogrtapnlatt:eRoenptlahceeuthpepedrooovrewni.th the model/serial On some models, the construction of this door is designed to withstand self-cleaning temperatures. \ oven frame hinge slot • Lift oven into cabinet cutout using the oven opening as an area to grip. shipping foot Push against seal area of front frame to push oven into cabinet until shipping feet almost contact cabinet. Use a Phillips screwdriver to remove screws attaching shipping feet. Remove and discard shipping feet. Push oven completely into cabinet and center oven in cabinet cutout. J J J J • Important: Securely fasten oven to cabinet using the screws provided (two screws for a single oven or four screws for a double oven). Insert the screws through holes in mounting rails. Do Not overtighten screws. Slide top of trim up, Pushtrim into place. Replace trim screw. • Slide top end of each trim upward onto oven side rails. Push each trim into place at bottom of trim. Use screws to attach each trim to oven. Take care not to scratch other surfaces with ends of trim. Ii!#i IC,eo°,,erot,o. 0 • Turn on power supply. The display panel will light up briefly. "PF" should appear in the temperature display. BAKE BROIL Check the operation of your single oven. Press the "BROIL" pad. "BROIL" will appear in the display. Press the "START" pad. Make sure the oven door is closed and the "ON" light is shown in the display area. After 2 minutes, partially open oven door. You should feel heat from the oven. Press the "CANCEL" pad. Check the operation of your double oven. Press the "Upper Oven" pad. Press the "BROIL" pad. "BROIL" will appear in the display. Press the "START" pad. Make sure the oven door is closed and the "ON" light is shown in the display area. After 2 minutes, partially open oven door. You should feel heat from the oven. Press the "CANCEL" pad. Press the "Lower Oven" pad and repeat the steps you completed for checking the upper oven. Page 3 door hinge • Rinespelraticneg theendssinogflehionrgeusppinetroohveinngedosolor tbsyin oven frame. Push behind each hinge so that hinges are pushed into oven frame as far as they will go. Open door and remove both door removal pins. Close and open door to check that door closes and opens completely. If door does not close or open completely, you have not pushed hinges completely into frame. Repeat door removal step and reinsert door into hinge slots again. Repeat for lower oven door. If your oven does not heat or an "F", followed by a number, appears in the display, contact your dealer or check the "If you need service..." section of this Installation Instructions. To get the most efficient use from your new oven, read your Use and Care Guide. Keep Installation Instructions and Guide close to oven for easy reference.