Xerox 6180N DocuSP Getting Started - Page 15

Saving stock and tray mappings

Get Xerox 6180N - Phaser Color Laser Printer PDF manuals and user guides
UPC - 095205425307
View all Xerox 6180N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

DOCUSP 4.1 2. Type mount /XRXbackup to mount the backup partition. 3. Type cd /XRXbackup. 4. Copy or ftp the backup files to the /XRXbackup partition from the storage location. ♦ If it is desirable to store the system backup files to tape, refer to the Tools and Utilities section of this document for the TGBackup procedure. ♦ When restoring a system backup, a DocuSP System Restore CD is provided with the software kit to your Xerox Service Representatie. Performing the following to start the Restore procedure: 1. Insert DocuSP System Restore CD in the CDROM drive. 2. Shutdown the DocuSP controller by selecting Shutdown from the DocuSP user interface. 3. At the ok> prompt, type boot cdrom. 4. During the system restore process, a series of questions displays asking if you wish to create a new file system. Enter yes. ♦ If a system restore is being performed following a fatal disk failure or replacement of the hard disks, a DocuSP clean install must be performed first to partition the hard drives and create the partitions. Following the clean install, copy the backup files to the /XRXbackup partition then perform the system restore. ♦ For a configuration backup, do not use the /XRXbackup partition to store the configuration files. The configuration backup files can be stored on the DocuSP internal disk, an external disk, an NFS mounted network drive, or supported media such as a floppy drive or CDROM R/W. Saving stock and tray mappings DocuSP 4.1 now provides the ability to save the current paper tray programming to a file and recall that file for later use. The saved tray mappings may also be copied to another DocuSPbased system using the DocuSP Backup and Restore functionality. For example, if a job or series of jobs that are often run have a specific paper tray programming, the mapping can be saved and recalled for faster setup for printing of the job. This functionality is not available on the DocuColor iGen3. XEROX DOCUMENT SERVICES PLATFORM SERIES 11 GETTING STARTED

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
DOCUSP 4.1
2. Type
mount /XRXbackup
to mount the backup
partition.
3. Type
cd /XRXbackup
.
4.
Copy or ftp the backup files to the /XRXbackup
partition from the storage location.
If it is desirable to store the system backup files to tape,
refer to the Tools and Utilities section of this document for
the TGBackup procedure.
♦
♦
♦
♦
When restoring a system backup, a DocuSP System
Restore CD is provided with the software kit to your Xerox
Service Representatie.
Performing the following to start
the Restore procedure:
1.
Insert DocuSP System Restore CD in the CDROM
drive.
2.
Shutdown the DocuSP controller by selecting
Shutdown from the DocuSP user interface.
3. At the ok> prompt, type
boot cdrom
.
4.
During the system restore process, a series of
questions displays asking if you wish to create a new
file system.
Enter
yes
.
If a system restore is being performed following a fatal
disk failure or replacement of the hard disks, a DocuSP
clean install must be performed first to partition the hard
drives and create the partitions.
Following the clean
install, copy the backup files to the /XRXbackup partition
then perform the system restore.
For a configuration backup, do not use the /XRXbackup
partition to store the configuration files.
The configuration
backup files can be stored on the DocuSP internal disk,
an external disk, an NFS mounted network drive, or
supported media such as a floppy drive or CDROM R/W.
Saving stock and tray mappings
DocuSP 4.1 now provides the ability to save the current paper
tray programming to a file and recall that file for later use.
The
saved tray mappings may also be copied to another DocuSP-
based system using the DocuSP Backup and Restore
functionality.
For example, if a job or series of jobs that are often run have a
specific paper tray programming, the mapping can be saved and
recalled for faster setup for printing of the job.
This functionality is not available on the DocuColor iGen3.
XEROX DOCUMENT SERVICES PLATFORM SERIES
11
GETTING STARTED