Yamaha DGX-630 Owner's Manual - Page 12

Put the keyboard on the stand., Post-assembly checklist, Once you've assembled the stand

Page 12 highlights

Setting Up 5-6 y 5 x 16 mm roundhead screws b Put the keyboard on the stand. Check the back-to-front orientation for stand, and carefully place the keyboard on the side boards. Slowly move the keyboard so that the holes on the bottom of the keyboard are properly aligned with the holes on the angle brackets. CAUTION • Be careful not to drop the keyboard or to get your fingers caught between the keyboard and the stand parts. n Install the keyboard to the stand. Fix the keyboard to the angle brackets, using the screws y. ■ Post-assembly checklist Once you've assembled the stand, check the following points: • Are there any parts left over? ➔ If so, read the assembly instructions again and correct any errors you might have made. • Is the instrument clear of doors and other movable fixtures? ➔ If not, move the instrument to an appropriate location. • Does the instrument make a rattling noise when you play it or move it? ➔ If so, properly tighten all screws. • Also, if the keyboard makes a creaking noise or seems unsteady when you play it, refer carefully to the assembly instructions and diagrams and retighten all screws. 12 DGX-630/YPG-635 Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154

12
DGX-630/YPG-635
Owner’s Manual
Setting Up
b
Put the keyboard on the stand.
Check the back-to-front orientation for stand, and care-
fully place the keyboard on the side boards. Slowly move
the keyboard so that the holes on the bottom of the key-
board are properly aligned with the holes on the angle
brackets.
n
Install the keyboard to the stand.
Fix the keyboard to the angle brackets, using the screws
y
.
5–6
y
5 x 16 mm
roundhead
screws
Post-assembly checklist
Once you’ve assembled the stand, check the fol-
lowing points:
• Are there any parts left over?
If so, read the assembly instructions again and correct
any errors you might have made.
• Is the instrument clear of doors and other movable
fixtures?
If not, move the instrument to an appropriate location.
• Does the instrument make a rattling noise when you
play it or move it?
If so, properly tighten all screws.
• Also, if the keyboard makes a creaking noise or
seems unsteady when you play it, refer carefully to
the assembly instructions and diagrams and
retighten all screws.
Be careful not to drop the keyboard or to get your fingers caught
between the keyboard and the stand parts.
CAUTION