ZyXEL P-964 User Guide - Page 41

Appendix B, Important Safety Instructions

Get ZyXEL P-964 PDF manuals and user guides View all ZyXEL P-964 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

P964 APR Cable Router with 802.11g Access Point Appendix B Important Safety Instructions The following safety instructions apply to the P964 APR: Be sure to read and follow all warning notices and instructions. Care must be taken to allow sufficient air circulation or space between units when the P964 APR is installed inside a closed rack assembly. The operating ambient temperature of the rack environment might be greater than room temperature. The maximum recommended ambient temperature for the P964 APR is 40ºC (104ºF). Installation in a rack without sufficient airflow can be unsafe. Racks should safely support the combined weight of all equipment. The connections and equipment that supply power to the P964 APR should be capable of operating safely with the maximum power requirements of the P964 APR. In case of a power overload, the supply circuits and supply wiring should not become hazardous. The input rating of the P964 APR is printed on the nameplate. The AC adapter must plug in to the right supply voltage, i.e. 120VAC adapter for North America and 230VAC adapter for Europe. Make sure that the supplied AC voltage is correct and stable. If the input AC voltage is over 10% lower than the standard may cause the P964 APR to malfunction. Installation in restricted access areas must comply with Articles 110-16, 110-17, and 110-18 of the National Electrical Code, ANSI/NFPA 70. Do not allow anything to rest on the power cord of the AC adapter, and do not locate the product where anyone can walk on the power cord. Do not service the product by yourself. Opening or removing covers can expose you to dangerous high voltage points or other risks. Refer all servicing to qualified service personnel. Generally, when installed after the final configuration, the product must comply with the applicable safety standards and regulatory requirements of the country in which it is installed. If necessary, consult the appropriate regulatory agencies and inspection authorities to ensure compliance. A rare condition can create a voltage potential between the earth grounds of two or more buildings. If products installed in separate building are interconnected, the voltage potential can cause a hazardous condition. Consult a qualified electrical consultant to determine whether or not this phenomenon exists and, if necessary, implement corrective action before interconnecting the products. If the equipment is to be used with telecommunications circuit, take the following precautions: Never install wiring during a lightning storm. Never install jacks in wet location unless the jack is specially designed for wet location. Never touch uninsulated wires or terminals unless the line has been disconnected at the network interface. Use caution when installing or modifying lines during an electrical storm. There is a remote risk of electric shock from lightning. Safety Instructions C

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
P964 APR
Cable Router with 802.11g Access Point
Safety Instructions
C
Appendix B
Important Safety Instructions
The following safety instructions apply to the P964 APR:
Be sure to read and follow all warning notices and instructions. Care must be taken to allow sufficient air circulation or space
between units when the P964 APR is installed inside a closed rack assembly. The operating ambient temperature of the rack
environment might be greater than room temperature. The maximum recommended ambient temperature for the P964 APR is 40ºC
(104ºF). Installation in a rack without sufficient airflow can be unsafe. Racks should safely support the combined weight of all
equipment.
The connections and equipment that supply power to the P964 APR should be capable of operating safely with the maximum power
requirements of the P964 APR. In case of a power overload, the supply circuits and supply wiring should not become hazardous. The
input rating of the P964 APR is printed on the nameplate.
The AC adapter must plug in to the right supply voltage, i.e. 120VAC adapter for North America and 230VAC adapter for Europe.
Make sure that the supplied AC voltage is correct and stable. If the input AC voltage is over 10% lower than the standard may cause
the P964 APR to malfunction.
Installation in restricted access areas must comply with Articles 110-16, 110-17, and 110-18 of the National Electrical Code,
ANSI/NFPA 70.
Do not allow anything to rest on the power cord of the AC adapter, and do not locate the product where anyone can walk on the
power cord. Do not service the product by yourself. Opening or removing covers can expose you to dangerous high voltage points or
other risks. Refer all servicing to qualified service personnel.
Generally, when installed after the final configuration, the product must comply with the applicable safety standards and regulatory
requirements of the country in which it is installed. If necessary, consult the appropriate regulatory agencies and inspection
authorities to ensure compliance.
A rare condition can create a voltage potential between the earth grounds of two or more buildings. If products installed in separate
building are interconnected, the voltage potential can cause a hazardous condition. Consult a qualified electrical consultant to determine
whether or not this phenomenon exists and, if necessary, implement corrective action before interconnecting the products. If the
equipment is to be used with telecommunications circuit, take the following precautions:
Never install wiring during a lightning storm.
Never install jacks in wet location unless the jack is specially designed for wet location.
Never touch uninsulated wires or terminals unless the line has been disconnected at the network interface.
Use caution when installing or modifying lines during an electrical storm. There is a remote risk of electric shock from lightning.