eMachines EL1358G eMachines EL1358 Service Guide - Page 70

Clearing CMOS, To clear the CMOS data

Get eMachines EL1358G PDF manuals and user guides View all eMachines EL1358G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

Clearing CMOS You may need to clear the Setup configuration values (CMOS) if the configuration has been corrupted, or if incorrect settings made in the Setup Utility caused error messages to be unreadable. This procedure will clear the BIOS supervisor password as well. Use the JBIOS1 jumper to clear the CMOS data. • 1-2 position: Normal operation (default) • 2-3 position: Clear CMOS data To clear the CMOS data: 1. Turn off the power to the computer and all peripherals. 2. Unplug the power cord from the computer. 3. Unplug the network cable and all connected peripheral devices from the computer. 4. Place the computer on a flat, steady surface. 5. Remove the side panel. 6. If necessary, remove any expansion cards, assemblies or cables that prevent access to the CMOS clear jumper. 7. Locate the JBIOS1 jumper on the mainboard. 8. Remove the jumper block and set it over the 2-3 pins for 20 to 30 seconds. 9. Return the jumper block to its default 1-2 position. 10. Reinstall any expansion card, peripheral, and system cables that have previously been removed. 11. Reinstall the side panel. 12. Connect the AC power cord to the system. 13. Press the power button to turn on the computer. 14. During POST, press Delete to access the Setup Utility. 15. Press F9 to load the system default values. 16. Press F10 to save the changes you made and close the Setup Utility. 62 EL1358 Service Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
62
EL1358 Service Guide
Clearing CMOS
You may need to clear the Setup configuration values (CMOS) if the configuration has been corrupted, or if
incorrect settings made in the Setup Utility caused error messages to be unreadable. This procedure will clear
the BIOS supervisor password as well.
Use the JBIOS1 jumper to clear the CMOS data.
•
1-2 position: Normal operation (default)
•
2-3 position: Clear CMOS data
To clear the CMOS data:
1.
Turn off the power to the computer and all peripherals.
2.
Unplug the power cord from the computer.
3.
Unplug the network cable and all connected peripheral devices from the computer.
4.
Place the computer on a flat, steady surface.
5.
Remove the side panel.
6.
If necessary, remove any expansion cards, assemblies or cables that prevent access to the CMOS clear
jumper.
7.
Locate the JBIOS1 jumper on the mainboard.
8.
Remove the jumper block and set it over the 2-3 pins for 20 to 30 seconds.
9.
Return the jumper block to its default 1-2 position.
10.
Reinstall any expansion card, peripheral, and system cables that have previously been removed.
11.
Reinstall the side panel.
12.
Connect the AC power cord to the system.
13.
Press the power button
to turn on the computer.
14.
During POST, press
Delete
to access the Setup Utility.
15.
Press
F9
to load the system default values.
16.
Press
F10
to save the changes you made and close the Setup Utility.