2014 Polaris Turbo IQ LXT Owners Manual - Page 78

2014 Polaris Turbo IQ LXT Manual

Get 2014 Polaris Turbo IQ LXT PDF manuals and user guides View all 2014 Polaris Turbo IQ LXT manuals

Page 78 highlights

OPERATION Break-In Period Engine Break-In The break-in period for the engine is the first 500 miles (800 km) of operation. No single action on your part is as important as following the procedures for a proper break-in. Careful treatment of a new engine and drive components will result in more efficient performance and longer life for these components. NOTICE: Excessive heat build-up during the first 500 miles (800 km) of operation will damage close-fitting engine parts. Do not operate at full throttle or high speeds for extended periods during the break-in period. NOTICE: Use of non-recommended oil may cause serious engine damage. Always use the recommended oil for your POLARIS snowmobile. 1. Fill the fuel tank with the recommended fuel. See page 81. 2. Check the oil level in the oil tank. See page 94. Add oil if necessary to maintain at the recommended level. 3. Drive slowly at first. Vary the throttle positions. Do not operate at sustained idle. 4. Perform regular checks on fluid levels, controls and areas outlined on the daily pre-ride inspection checklist. See page 66. 5. During the break-in period, change both the oil and the filter at 500 miles (800 km) or before seasonal storage, whichever comes first. Drive Belt Break-In The break-in period for a new drive belt is 30 miles (48 km). During this time, vary the throttle position under 50% and limit full throttle use. New drive belts should be washed with warm, soapy water and allowed to air dry prior to use. Always take time to warm up the belt and driveline prior to operating the snowmobile. Free the track and skis from the ground before engaging throttle. 76

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
76
OPERATION
Break-In Period
Engine Break-In
The break-in period for the engine is the first 500 miles (800 km) of
operation. No single action on your part is as important as following the
procedures for a proper break-in. Careful treatment of a new engine and
drive components will result in more efficient performance and longer
life for these components.
NOTICE:
Excessive heat build-up during the first 500 miles (800 km) of
operation will damage close-fitting engine parts. Do not operate at full
throttle or high speeds for extended periods during the break-in
period.
NOTICE:
Use of non-recommended oil may cause serious engine damage.
Always use the recommended oil for your POLARIS snowmobile.
1.
Fill the fuel tank with the recommended fuel. See page 81.
2.
Check the oil level in the oil tank. See page 94. Add oil if necessary
to maintain at the recommended level.
3.
Drive slowly at first. Vary the throttle positions. Do not operate at
sustained idle.
4.
Perform regular checks on fluid levels, controls and areas outlined
on the daily pre-ride inspection checklist. See page 66.
5.
During the break-in period, change both the oil and the filter at 500
miles (800 km) or before seasonal storage, whichever comes first.
Drive Belt Break-In
The break-in period for a new drive belt is 30 miles (48 km). During this
time, vary the throttle position under 50% and limit full throttle use.
New drive belts should be washed with warm, soapy water and allowed
to air dry prior to use.
Always take time to warm up the belt and driveline prior to operating
the snowmobile. Free the track and skis from the ground before engag-
ing throttle.