AEG KSK782220M User Manual - Page 48

Steam Cleaning, Cleaning Reminder

Get AEG KSK782220M PDF manuals and user guides View all AEG KSK782220M manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

48 www.aeg.com 1 3 2 2. Pull the front end of the shelf support away from the side wall. 3. Pull the supports out of the rear catch. Install the shelf supports in the opposite sequence. 12.4 Steam Cleaning Remove as much dirt as possible manually. Remove the accessories and the shelf support to clean the side walls. The steam cleaning functions support the steam cavity cleaning of the appliance. For a better performance you should start the cleaning function when the appliance is cool. The specified time is related to the duration of the function and does not include the time required for cleaning of the cavity by the user. When the steam cleaning function is active, the light is off. 1. Fill the water drawer to the maximum level (around 950 ml of water) until the acoustic signal sounds or the display shows the message. 2. Choose the steam cleaning function in the menu: Cleaning. Steam Cleaning - the duration of the function is around 30 minutes. a) Activate the function. b) An acoustic signal sounds when the programme is completed. c) Touch a sensor field to deactivate the signal. Steam Cleaning Plus - the duration of the function is around 75 minutes. a) Spray a suitable detergent uniformly in the oven cavity on both enamel and steel parts. Before you start the cleaning procedure, make sure that the appliance is cold. b) Activate the function. After around 50 minutes an acoustic signal sounds when the first part of the programme is completed. c) Press . This is not the end of the cleaning procedure. Follow the message in the display to complete the cleaning. d) Wipe the internal surface of the appliance with a non-abrasive surface care sponge. You can use warm water or oven detergents to clean the cavity. e) Press . The final part of the procedure starts. The duration of this stage is around 25 minutes. 3. Wipe the internal surface of the appliance with a non-abrasive sponge. You can use warm water to clean the cavity. After cleaning keep the appliance door open for approximately 1 hour. Wait until the appliance is dry. To speed up the drying you can heat up the appliance with hot air at temperature 150 °C for approximately 15 minutes. You can get maximum effects of the cleaning function if you manually clean the appliance immediately after the function ends. 12.5 Cleaning Reminder When reminder is displayed cleaning is necessary. Perform the function Steam Cleaning Plus. You can enable / disable the function: Cleaning Reminder in the menu: Basic Settings.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
2
3
1
2.
Pull the front end of the shelf support
away from the side wall.
3.
Pull the supports out of the rear
catch.
Install the shelf supports in the opposite
sequence.
12.4
Steam Cleaning
Remove as much dirt as possible
manually.
Remove the accessories and the shelf
support to clean the side walls.
The steam cleaning functions support
the steam cavity cleaning of the
appliance.
For a better performance
you should start the cleaning
function when the appliance
is cool.
The specified time is related
to the duration of the
function and does not
include the time required for
cleaning of the cavity by the
user.
When the steam cleaning function is
active, the light is off.
1.
Fill the water drawer to the maximum
level (around 950 ml of water) until
the acoustic signal sounds or the
display shows the message.
2.
Choose the steam cleaning function
in the menu: Cleaning.
Steam Cleaning
- the duration of the
function is around 30 minutes.
a)
Activate the function.
b)
An acoustic signal sounds when
the programme is completed.
c)
Touch a sensor field to
deactivate the signal.
Steam Cleaning Plus
- the duration
of the function is around 75 minutes.
a)
Spray a suitable detergent
uniformly in the oven cavity on
both enamel and steel parts.
Before you start the cleaning
procedure, make sure that the
appliance is cold.
b)
Activate the function.
After around 50 minutes an
acoustic signal sounds when the
first part of the programme is
completed.
c)
Press
.
This is not the end of
the cleaning
procedure. Follow
the message in the
display to complete
the cleaning.
d)
Wipe the internal surface of the
appliance with a non-abrasive
surface care sponge. You can use
warm water or oven detergents
to clean the cavity.
e)
Press
.
The final part of the procedure
starts. The duration of this stage
is around 25 minutes.
3.
Wipe the internal surface of the
appliance with a non-abrasive
sponge. You can use warm water to
clean the cavity.
After cleaning keep the appliance door
open for approximately 1 hour. Wait until
the appliance is dry. To speed up the
drying you can heat up the appliance
with hot air at temperature 150 °C for
approximately 15 minutes. You can get
maximum effects of the cleaning function
if you manually clean the appliance
immediately after the function ends.
12.5
Cleaning Reminder
When reminder is displayed cleaning is
necessary. Perform the function Steam
Cleaning Plus.
You can enable / disable the function:
Cleaning Reminder in the menu: Basic
Settings.
www.aeg.com
48