AIWA NSX-V9000 Operating Instructions - Page 14

Basic Recording - cd player

Get AIWA NSX-V9000 PDF manuals and user guides View all AIWA NSX-V9000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

BASIC RECORDING This section explains how to record from the tuner, CD player, or external equipment. .', ._ ,,. ,_ 4 '1 Preparation q Set the tape to the point where recording will start. q Use Type I (normal) and Type II (high/CrOz) tapes for recording. 1 Insert the tape to be recorded on into deck 2. Insertthe tape with the side to be recordedon first facing out from the unit and the exposed side down. To stop recording, press the s button. To pause recording, press the 11 button. (Applicable when the source is TUNER, VIDEO/AUX.) To resume recording, press again. To start recording with the remote control First press the q/0 REC/REC MUTE button, and then press the + F button within 2 seconds. INSERTING BLANK SPACES Insertion of 4-second blank spaces enables activation of the Music Sensor function. (Applicable when the source is TUNER or VIDEO/AUX.) 1 Press the. REC/REC MUTE button during recording or while in recording pause mode. ~ on the display flashes for 4 seconds and the tape runs without recording. After 4 seconds, the deck enters the recording pause mode, 2 Press the II button to resume recording. To insert a blank space of less than 4 seconds, press the q REC/REC MUTE button again while ~ is flashing. To insert blank spaces of more than 4 seconds, after the deck enters recording pause mode, press the q REC/REC MUTE button again. Each time the button is pressed, a 4-second blank space is added. A I 4 2 Press the REV MODE button to select the reverse mode. To record on one side only, turn on =. To record on both sides, turn on 1) or C=). 3 Press the DOLBY NR button to turn Dolby NR on or off. To record with DOLBY NR, turn on m NR. To record without DOLBY NR, turn off UI NR. 4 Press one of the function buttons and prepare the source to be recorded. To record from a CD, press the CD button and load the disc(s). To record from a radio broadcast, press the TUNER button and tune in to a station. To record from the connected source, press the VIDEO/ AUX button and play. 5 Press the q REC/REC MUTE button to start recording. When the selected function is CD, playback and recording start simultaneously. 13 ENGLISH To erase a recording Make sure the microphone is not connected to this unit. 1 Insert the tape to be erased into deck 2 and press the TAPEI DECK 112 button to display "TAPE 2. 2 Set the tape to the point where the erasure is to be started. 3 Set the reverse mode by pressing the REV MODE button. 4 Press the q REC/REC MUTE button to start the erasure.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
BASIC RECORDING
This section explains how to record from the tuner, CD player, or
external equipment.
.’,
._
,,.
,_
4
‘1
Preparation
Set the tape to the point where recording will start.
Use Type I (normal) and Type II (high/CrOz) tapes for recording.
1
2
3
4
5
Insert the tape to be recorded
on into deck 2.
Insertthe tape with the side to be recordedon first facing
out from the unit
and the exposed side down.
A
I
4
Press the REV MODE button to select the reverse
mode.
To record on one side only, turn on =.
To record on both sides, turn on 1)
or C=).
Press the DOLBY NR button to turn Dolby NR on
or off.
To record with DOLBY NR, turn on m
NR.
To record without DOLBY NR, turn off UI
NR.
Press
one of the function
buttons
and prepare
the source
to be recorded.
To record from a CD,
press the CD button and load the
disc(s).
To record from a radio broadcast, press the TUNER button
and tune in to a station.
To record from the connected
source, press the VIDEO/
AUX
button and play.
Press
the
REC/REC
MUTE
button
to start
recording.
When the selected function
is CD, playback
and recording
start simultaneously.
To stop recording,
press the
button.
To pause recording,
press the 11 button. (Applicable when the
source is TUNER, VIDEO/AUX.)
To resume recording,
press
again.
To start recording with the remote control
First press the
/0
REC/REC
MUTE button, and then press
the + F
button within 2 seconds.
INSERTING
BLANK
SPACES
Insertion
of
4-second
blank spaces enables activation
of the
Music Sensor function. (Applicable when the source is TUNER
or VIDEO/AUX.)
1
2
Press the.
REC/REC MUTE button during recording or
while in recording
pause mode.
~
on the display flashes for 4 seconds and the tape runs
without recording. After 4
seconds,
the
deck
enters
the
recording pause mode,
Press the II
button to resume recording.
To insert a blank space of less than 4 seconds,
press the
REC/REC MUTE button again while ~
is flashing.
To insert blank spaces of more than 4 seconds,
after the
deck enters recording pause mode, press the
REC/REC MUTE
button again.
Each time the button is pressed, a 4-second blank
space is added.
To erase
a recording
Make sure the microphone
is not connected to this unit.
1
Insert the tape to be erased into deck 2 and press the TAPEI
DECK 112button to display “TAPE 2.
2
Set the tape to the point where the erasure is to be started.
3
Set the reverse mode by pressing the REV MODE button.
4
Press the
REC/REC MUTE button to start the erasure.
13
ENGLISH