AIWA XR-M35 Operating Instructions - Page 17

SETTING

THE TIMER

1

1,2,3,4

3

1

2,4

m

,/

6

......

-.-.’

The

unit can

be turned

on at a specified

time

every

day with

the

buil”:-in timer.

Preparation

Make

sure

the clock

is set correctly.

(See

page

5.)

Use the

remote

control.

7 Press theTIMER

button repeatedly

while pressing

the SHIFT

button

to display

0,

and press the

11

button

within

4 seconds.

@

is displayed,

and the

hour

flashes.

I‘

you

do not press

the

11 button

within

4 seconds,

another

CIperation

may

start.

2

[)esignate

the

hour

of

the

timer-on

time

by

pressing

the *

or _

button or by turning

the

!flULTl JOG dial, and press the 11 button.

Repeat

to designate

the minute

of the timer-on

time.

After

you designate

the timer-on

time,

one of the source

name

f ashes

alternately

on the display.

.3 Press the FUNCTION

button

repeatedly

to select

a source

and press the

Ii

button.

If

the TUNER

button

is pressed,

the band cannot

be selected

in this

step.

4

5

6

Select the duration

for the timer-activated

period

with

the

+<

or

F

button

or the

MULTI

JOG

dial, and press the

11 button.

The duration

for the timer-activated

period

can be set between

5 and 240

minutes

in 5-minute

steps.

Prepare

the source.

To listen to a CD,

load

the disc.

To listen to a tape,

insert

the tape

into the deck.

To listen to the radio,

select

the band and tune

into

a station.

To listen to an MD,

set the timer

of the MD recorder

(with

an

external

timer)

and

prepare

to play

the

MD.

To

listen

to the equipment

connected

to VIDEO/AUX,

set

the timer of the connected

source

(with an external

timer)

and prepare for the play.

Press the POWER

button to turn the unit off after

adjusting

the volume

and tone.

@

remains

on the display

after

the power

is turned

off (timer

standby

mode).

When

the

timer-on

time

is

reached,

the

unit

turns

on

and

begins

play

with

the selected

source.

To check the specified

time and source

Press

the TIMER

button

while

pressing

the SHIFT

button

on the

remote

control.

The timer-on

time

and the selected

source

name

are displayed

for 4 seconds.

However,

the duration

for the timer-

activated

period

will

not be displayed.

TIMER

RECORDING

Timer

recording

is applicable

for TUNER,

MD and

ViDEO/AUX

(with

an external

timer)

sources

only.

Press the TIMER

button

repeatedly

while

pressing

the

SHIFT

button

on the remote

control

so that @ and

~

appear

on the display,

and press the

11 button.

Repeat

the steps

shown

above

from

step

2 and

insert

the tape

to be recorded

into the deck

after

step

5.

To cancel

timer

standby

mode temporarily

Press

the TIMER

button

while

pressing

the SHIFT

button

on the

remote

control

so that

@ (and

~)

disappear

on the display.

To restore

the

timer

standby

mode,

press

again

to display

@

(and

~).

Using the unit while the timer

is set

You can

use the

unit normally

after

setting

the timer.

Before

turning

off the power,

repeat

step 5 to prepare

the source,

and adjust

the volume

and tone.

m

Timer

playback

and

timer

recording

will

not begin

unless

the

power

is turned

off.

Connected

equipment

cannot

be turned

on and off by the built-

in timer

of this

unit.

Use

an external

timer.

ENGLISH

16

AIWA XR-M35 Operating Instructions - Page 17

Setting, The Timer

Page 17 highlights