AIWA XR-M35 Operating Instructions - Page 6

BEFORE

OPERATION

SETTING

THE CLOCK

POWER – -@l

DEMO

Function

PHONES

m

U

-

sensor

Remote

,.-,

—

. .....

To

turn the unit on

Press

one of the function

buttons

(TAPE,

TUNER,

VIDEO/AUX,

CD,

MD).

Playback

of the

inserted

disc

or tape

begins,

or the

previously

tuned

station

is received

(Direct

Play

Function).

The

POWER

button

is also

available.

The

disc

compartment

may

open

and

close

to reset

the

unit.

Illumination

guides

Whenever

the AC cord is connected

or one of the function

buttons

is pressed,

the buttons

for that

operation

light

up or flash.

Example:

When

the AC cord

is connected,

the

II

button

flashes

as a guide

to setting

the current

time.

After

use

Press

the

POWER

button

to turn

off

the

power.

The

display

changes

to the clock.

MULTI JOG dial

The

MULTI

JOG

dial

can

be

used

when

tuning

in to a preset

station

or skipping

to the beginning

of a CD track.

it can also

be

used

with

the

MODE

button

as a convenient

dial

to adjust

the

sound

quality

and turn

Dolby

NR on or off.

Refer

to pages

6, 8,

9, and

11 for details.

Using the headphones

Connect

headphones

to the

PHONES

jack

with

a stereo

mini

plug

(03.5

mm,

l/s inch).

No sound

is output

from

the speakers

while

the headphones

are

plugged

in.

““m

1

2

3

4

5

6

II

1“””””””’”~

Ej

– CLOCK

–SHIFT

–44,

-

-

II

Press

the

CLOCK

button

while

pressing

the

SHIFT

button

on the remote

control.

Within

4 seconds,

press the

11 button.

The

hour

flashes.

To switch

to the 24-hour

standard,

press

the

button.

To restore

the

12-hour

standard,

press

the

button

again.

Press

the

<

or W

button

or turn the

MULTI

JOG dial to designate

the hour.

Press the

11 button

to set the hour.

The

hour

stops

flashing

and

the

minute

starts

flashing.

Press

the

+

or *

button

or turn

the MULTI

JOG dial to designate

the minute.

Press

the

II

button

to

set

the

minute

and

complete

setting.

The

minute

stops

flashing

on the display

and the clock

starts

from

00 seconds.

To

set the clock without

the remote

control

1 Turn

off

the

unit

if the

unit is powered.

Then,

if

the

demonstration

display

appears,

press

the

DEMO

button

to cancel

it.

2

Press the 1I button twice so that the hour flashes.

Carry

out then

the steps

3 to 6 above.

To

display the current time

Press

the

CLOCK

button

while

pressing

the SHIFT

button

on

the remote

control.

The time is displayed

for 4 seconds.

However,

the time

cannot

be displayed

during

recording.

If the clock display

flashes

while

the power

is off

This

is caused

by a power

interruption.

The

current

time

needs

to be reset.

If

power

is interrupted

for more

than

approximately

12 hours,

all

settings

stored

in memory

after

purchase

need

to be reset.

5

ENGLISH

AIWA XR-M35 Operating Instructions - Page 6

Before, Operation, Setting, The Clock - remote

Page 6 highlights