ASRock A785GM-LE User Manual - Page 25

Onboard Headers and Connectors - m black

Get ASRock A785GM-LE PDF manuals and user guides View all ASRock A785GM-LE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

2.8 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! • Floppy Connector (33-pin FLOPPY1) (see p.13 No. 25) Pin1 FLOPPY1 the red-striped side to Pin1 Note: Make sure the red-striped side of the cable is plugged into Pin1 side of the connector. Primary IDE connector (Blue) (39-pin IDE1, see p.13 No. 10) PIN1 IDE1 connect the blue end to the motherboard connect the black end to the IDE devices 80-conductor ATA 66/100/133 cable Note: Please refer to the instruction of your IDE device vendor for the details. Serial ATAII Connectors (SATAII_1 (PORT 0): see p.13, No. 19) (SATAII_2 (PORT 1): see p.13, No. 18) (SATAII_3 (PORT 2): see p.13, No. 17) (SATAII_4 (PORT 3): see p.13, No. 13) (SATAII_5 (PORT 4): see p.13, No. 12) (SATAII_6 (PORT 5): see p.13, No. 11) SATAII_4 SATAII_5 SATAII_6 (PORT 3) (PORT 4) (PORT 5) SATAII_1 SATAII_2 SATAII_3 (PORT 0) (PORT 1) (PORT 2) These six Serial ATAII (SATAII) connectors support SATAII or SATA hard disk for internal storage devices. The current SATAII interface allows up to 3.0 Gb/s data transfer rate. Serial ATA (SATA) Data Cable (Optional) Either end of the SATA data cable can be connected to the SATA / SATAII hard disk or the SATAII connector on the motherboard. 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
25
25
25
25
25
FLOPPY
1
Pin
1
the red-striped side to Pin1
2.8 Onboard Headers and Connectors
2.8 Onboard Headers and Connectors
2.8 Onboard Headers and Connectors
2.8 Onboard Headers and Connectors
2.8 Onboard Headers and Connectors
Onboard headers and connectors are NOT jumpers. Do NOT place
jumper caps over these headers and connectors. Placing jumper caps
over the headers and connectors will cause permanent damage of the
motherboard!
•
Floppy Connector
(33-pin FLOPPY1)
(see p.13 No. 25)
Note:
Make sure the red-striped side of the cable is plugged into Pin1 side of the
connector.
Primary IDE connector (Blue)
(39-pin IDE1, see p.13 No. 10)
Note:
Please refer to the instruction of your IDE device vendor for the details.
Serial ATAII Connectors
These six Serial ATAII (SATAII)
(SATAII_1 (PORT 0):
connectors support SATAII
see p.13, No. 19)
or SATA hard disk for internal
(SATAII_2 (PORT 1):
storage devices. The current
see p.13, No. 18)
SATAII interface allows up to
(SATAII_3 (PORT 2):
3.0 Gb/s data transfer rate.
see p.13, No. 17)
(SATAII_4 (PORT 3):
see p.13, No. 13)
(SATAII_5 (PORT 4):
see p.13, No. 12)
(SATAII_6 (PORT 5):
see p.13, No. 11)
Serial ATA (SATA)
Either end of the SATA data cable
Data Cable
can be connected to the SATA /
(Optional)
SATAII hard disk or the SATAII
connector on the motherboard.
connect
the black end
to the IDE devices
connect the blue end
to the motherboard
IDE
1
PIN1
80-conductor ATA 66/100/133 cable
SATAII_4
SATAII_5
SATAII_6
(PORT 3)
(PORT 4)
(PORT 5)
SATAII_1
SATAII_2
SATAII_3
(PORT 0)
(PORT 1)
(PORT 2)