Adaptec 51645 User Guide - Page 65

Disk Drive Failure in a RAID 0 Array, Multiple Failures in the Same Array, Failed Drive in MaxIQ Pool - firmware download

Page 65 highlights

Chapter 10: Solving Problems ● 65 If there are more disk drive failures than hot spares, see Failed Disk Drive Not Protected by a Hot Spare. If copyback is enabled, data is moved back to its original location once the controller detects that the failed drive has been replaced. Disk Drive Failure in a RAID 0 Array Because RAID 0 volumes do not include redundancy, if a disk drive fails in a RAID 0 array, the data can't be recovered. Correct the cause of the failure or replace the failed disk drives. Then, restore your data (if available). Multiple Failures in the Same Array Except in RAID 6 and RAID 60 arrays (see page 74), if more than one disk drive fails at the same time in the same array, the data normally can't be recovered. You may be able to recover the data by forcing the logical drive online or by recreating the logical drive without the initialization step. You can use the BIOS utility, ACU (see page 61), the command-line utility, ARCCONF, or Adaptec Storage Manager. For more information, refer to the Adaptec RAID Controller Command Line Interface User's Guide and the Adaptec. Storage Manager User's Guide. Note: In some instances, RAID 10 and RAID 50 arrays may survive multiple disk drive failures, depending on which disk drives fail. Failed Drive in MaxIQ Pool Because Solid State Drives (SSD) in the MaxIQ pool are just used for caching, not permanent storage, no data recovery or rebuilding is necessary. Once you identify the failed SSD, for example, by using Adaptec Storage Manager's rapid fault isolation feature, replace the failed SSD with a new one (see page 40), then add the SSD to the MaxIQ pool following the instructions on page 88 or by using Adaptec Storage Manager; the new SSD is not added to the MaxIQ pool automatically. Resetting the Controller This section explains how to reset (or Mode 0 flash) your Adaptec RAID controller. You may want to do this if the controller becomes inoperable, or if a firmware upgrade is unsuccessful. To reset your Adaptec RAID controller: 1 Download the firmware version currently installed on your controller from www.adaptec.com 2 Extract the downloaded files to a folder on your local hard drive (for example, C:\Download\Drivers). 3 Create a bootable MS-DOS floppy disk and copy the AFU.exe file to it. Copy the first firmware image to the same floppy disk. 4 Create additional bootable MS-DOS floppy disks and copy each additional firmware image to its own floppy disk.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135

Chapter 10: Solving Problems
65
If there are more disk drive failures than hot spares, see
Failed Disk Drive Not Protected by a Hot
Spare
.
If copyback is enabled, data is moved back to its original location once the controller detects
that the failed drive has been replaced.
Disk Drive Failure in a RAID 0 Array
Because RAID 0 volumes do not include redundancy, if a disk drive fails in a RAID 0 array, the
data can’t be recovered.
Correct the cause of the failure or replace the failed disk drives. Then, restore your data (if
available).
Multiple Failures in the Same Array
Except in RAID 6 and RAID 60 arrays (see
page 74
), if more than one disk drive fails at the
same time in the same array, the data normally can’t be recovered.
You
may
be able to recover the data by forcing the logical drive online or by recreating the
logical drive without the initialization step. You can use the BIOS utility, ACU (see
page 61
),
the command-line utility, ARCCONF, or Adaptec Storage Manager. For more information,
refer to the
Adaptec RAID Controller Command Line Interface User’s Guide
and the
Adaptec.
Storage Manager User’s Guide
.
Note:
In some instances, RAID 10 and RAID 50 arrays
may
survive multiple disk drive failures,
depending on which disk drives fail.
Failed Drive in MaxIQ Pool
Because Solid State Drives (SSD) in the MaxIQ pool are just used for caching, not permanent
storage, no data recovery or rebuilding is necessary. Once you identify the failed SSD, for
example, by using
Adaptec Storage Manager’s
rapid fault isolation feature, replace the failed
SSD with a new one (see
page 40
), then add the SSD to the MaxIQ pool following the
instructions on
page 88
or by using
Adaptec Storage Manager
; the new SSD is
not
added to the
MaxIQ pool automatically.
Resetting the Controller
This section explains how to reset (or
Mode 0
flash
) your Adaptec RAID controller. You may
want to do this if the controller becomes inoperable, or if a firmware upgrade is unsuccessful.
To reset your Adaptec RAID controller:
1
Download the firmware version currently installed on your controller from
www.adaptec.com
2
Extract the downloaded files to a folder on your local hard drive (for example,
C:\Download\Drivers).
3
Create a bootable MS–DOS floppy disk and copy
the AFU.exe file to it. Copy the first
firmware image to the same floppy disk.
4
Create additional bootable MS–DOS floppy disks and copy each additional firmware
image to its own floppy disk.