Adaptec AAA-133U2 Hardware Guide - Page 47

Windows NT Boot disk installation, Windows NT Boot CD-ROM installation, Adaptec CI/O Man, agement

Get Adaptec AAA-133U2 - AAA 133 RAID Controller PDF manuals and user guides
UPC - 760884134337
View all Adaptec AAA-133U2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Installing the Software Driver for Windows NT 2 Windows NT Boot disk installation: When prompted, insert disk #2 in your floppy drive. After a few moments you will see a blue screen. To setup Windows NT now, press Enter and continue with Step 3 below. Windows NT Boot CD-ROM installation: When the following message appears onscreen, press the F6 key and skip to Step 4 below. Setup is inspecting your computer system's hardware... 3 Press S to skip autodetection of your SCSI host adapter. 4 Press S again to specify an additional device. 5 Press Enter to select Others; insert the Adaptec Array1000U2 Family Manager Set driver disk in your floppy disk drive and press Enter. 6 The screen displays the adapter drivers supported on the disk. Select the Adaptec Array1000U2 Family Adapter driver and press Enter. 7 If you want to add drivers (other than for the AAA-131U2/ 133U2), press S and repeat Step 5 for each additional adapter and insert the appropriate disk provided by the hardware manufacturer. 8 Press Enter to continue with the Windows NT operating system setup. Follow the instructions onscreen and in the Windows NT documentation to complete the installation. 9 When Windows NT installation is complete, install Adaptec CI/O Management Software. Refer to the Adaptec CI/O Management Software User's Guide for instructions on installing and using the software. 4-3 Downloaded from www.Manualslib.com manuals search engine

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
4-3
Installing the Software Driver for Windows NT
2
Windows NT Boot disk installation
: When prompted, insert
disk #2 in your floppy drive. After a few moments you will see
a blue screen. To setup Windows NT now, press
Enter
and con-
tinue with Step 3 below.
Windows NT Boot CD-ROM installation
: When the following
message appears onscreen, press the
F6
key and skip to Step 4
below.
Setup is inspecting your computer system’s hardware…
3
Press
S
to skip autodetection of your SCSI host adapter.
4
Press
S
again to specify an additional device.
5
Press
Enter
to select
Others
; insert the Adaptec Array1000U2
Family Manager Set driver disk in your floppy disk drive
and press
Enter
.
6
The screen displays the adapter drivers supported on the disk.
Select the
Adaptec Array1000U2 Family Adapter
driver and
press
Enter
.
7
If you want to add drivers (other than for the AAA-131U2/
133U2), press
S
and repeat Step 5 for each additional adapter
and insert the appropriate disk provided by the hardware
manufacturer.
8
Press
Enter
to continue with the Windows NT operating
system setup. Follow the instructions onscreen and in the
Windows NT documentation to complete the installation.
9
When Windows NT installation is complete, install Adaptec
CI/O Management Software. Refer to the
Adaptec CI/O Man-
agement Software User’s Guide
for instructions on installing and
using the software.
Downloaded from
www.Manualslib.com
manuals search engine