Adaptec AAA-133U2 Hardware Guide - Page 60

Installing the Array1000U2 Driver for UnixWare

Get Adaptec AAA-133U2 - AAA 133 RAID Controller PDF manuals and user guides
UPC - 760884134337
View all Adaptec AAA-133U2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

AAA-130U2 Series Installation and Hardware Guide Installing the Array1000U2 Driver for UnixWare To begin driver installation, see either Installing the Driver When Installing SCO UnixWare below, or Installing the Driver When SCO UnixWare is Already Installed on page 6-3. Installing the Driver When Installing SCO UnixWare To install the cda1000 driver at the same time you install SCO UnixWare, follow the instructions below: 1 Insert the SCO UnixWare Installation disk in the floppy boot drive. Reboot your computer. Wait for the first SCO UnixWare installation screen and prompt to appear, then follow the onscreen instructions. 2 When prompted to Install HBA Diskette, first remove the Installation disk, then insert the Adaptec Array1000U2 Family Manager Set driver disk for SCO UnixWare into your floppy disk drive. 3 Select Install HBA Diskette and press F10. 4 If you have additional HBA disks, insert the next HBA disk, select Install HBA Diskette and press F10. If all of your HBA disks have been installed, select Proceed With Installation and press F10. (Do not reinstall the cda1000 HBA disk.) 5 If necessary, enter the DCU (Device Configuration Utility) to view/change the SCO UnixWare device driver configuration data; otherwise select Continue With Installation. 6 When prompted, reinsert the HBA disk (Adaptec Array1000U2 Family Manager Set driver disk for SCO UnixWare) that you inserted in Step 3 above, and press Enter. 7 Follow the onscreen instructions to complete the installation. Note: If your installation fails, do not attempt to use the update installation pkgadd procedure to fix the installation. Follow the instructions in the SCO UnixWare documentation and in this document to retry the installation. 6-2 Downloaded from www.Manualslib.com manuals search engine

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
6-2
AAA-130U2 Series Installation and Hardware Guide
Installing the Array1000U2 Driver for UnixWare
To begin driver installation, see either
Installing the Driver When
Installing SCO UnixWare
below, or
Installing the Driver When SCO
UnixWare is Already Installed
on page 6-3.
Installing the Driver When Installing SCO UnixWare
To install the
cda1000
driver at the same time you install SCO
UnixWare, follow the instructions below:
1
Insert the SCO UnixWare Installation disk in the floppy boot
drive. Reboot your computer.
Wait for the first SCO UnixWare installation screen and prompt
to appear, then follow the onscreen instructions.
2
When prompted to Install HBA Diskette, first remove the
Installation disk, then insert the Adaptec Array1000U2 Family
Manager Set driver disk for SCO UnixWare into your floppy
disk drive.
3
Select
Install HBA Diskette
and press
F10
.
4
If you have additional HBA disks, insert the next HBA disk,
select
Install HBA Diskette
and press
F10
.
If all of your HBA disks have been installed, select
Proceed
With Installation
and press
F10
. (Do not reinstall the
cda1000
HBA disk.)
5
If necessary, enter the DCU (Device Configuration Utility) to
view/change the SCO UnixWare device driver configuration
data; otherwise select
Continue With Installation
.
6
When prompted, reinsert the HBA disk (Adaptec Array1000U2
Family Manager Set driver disk for SCO UnixWare) that you
inserted in Step 3 above, and press
Enter
.
7
Follow the onscreen instructions to complete the installation.
Note:
If your installation fails, do not attempt to use the
update installation
pkgadd
procedure to fix the installation.
Follow the instructions in the SCO UnixWare documenta-
tion and in this document to retry the installation.
Downloaded from
www.Manualslib.com
manuals search engine