Adaptec AAA-133U2 Hardware Guide - Page 61

Installing the Driver When SCO UnixWare is Already Installed

Get Adaptec AAA-133U2 - AAA 133 RAID Controller PDF manuals and user guides
UPC - 760884134337
View all Adaptec AAA-133U2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

Installing the Software Driver for SCO UnixWare 8 When SCO UnixWare installation is complete, install Adaptec CI/O Management Software. Refer to the Adaptec CI/O Management Software User's Guide for instructions on installing and using the software. Installing the Driver When SCO UnixWare is Already Installed To update or install the cda1000 driver on a system where SCO UnixWare is already installed, follow the instructions below: 1 At the system prompt, type the following and press Enter: pkgadd -d diskette1 2 Follow the instructions onscreen to insert the HBA disk (the Adaptec Array1000U2 Family Manager Set driver disk for SCO UnixWare) into your floppy disk drive and press Enter. 3 When prompted to select packages, select all packages (press Return). The package is loaded into your SCO UnixWare operating system. 4 When the package has loaded, you may be prompted to install the disk again. Do not reinsert the HBA disk (Adaptec Array1000U2 Family Manager Set driver disk for SCO UnixWare). Instead, type q (quit) and press Enter. 5 Shutdown or reboot the system. 6 When prompted to rebuild the kernel, select go. 7 When driver installation is complete, install Adaptec CI/O Management Software. Refer to the Adaptec CI/O Management Software User's Guide for instructions on installing and using the software. Ì 6-3 Downloaded from www.Manualslib.com manuals search engine

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
6-3
Installing the Software Driver for SCO UnixWare
8
When SCO UnixWare installation is complete, install Adaptec
CI/O Management Software. Refer to the
Adaptec CI/O Man-
agement Software User’s Guide
for instructions on installing and
using the software.
Installing the Driver When SCO UnixWare is Already Installed
To update or install the
cda1000
driver on a system where SCO
UnixWare is already installed, follow the instructions below:
1
At the system prompt, type the following and press
Enter
:
pkgadd -d diskette1
2
Follow the instructions onscreen to insert the HBA disk (the
Adaptec Array1000U2 Family Manager Set driver disk for SCO
UnixWare) into your floppy disk drive and press
Enter
.
3
When prompted to select packages, select all packages (press
Return
). The package is loaded into your SCO UnixWare oper-
ating system.
4
When the package has loaded, you may be prompted to install
the disk again. Do not reinsert the HBA disk (Adaptec
Array1000U2 Family Manager Set driver disk for SCO
UnixWare). Instead, type
q
(quit) and press
Enter
.
5
Shutdown or reboot the system.
6
When prompted to rebuild the kernel, select
go
.
7
When driver installation is complete, install Adaptec CI/O
Management Software. Refer to the
Adaptec CI/O Management
Software User’s Guide
for instructions on installing and using
the software.
Downloaded from
www.Manualslib.com
manuals search engine