Airlink AML001 Manual - Page 45

Disables protocol result code appended to DCE speed.

Get Airlink AML001 PDF manuals and user guides View all Airlink AML001 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

PCI Modem Card User's Manual \Q0 Disables flow control (same as &K0). \Q1 XON/XOFF software flow control (same as &K4). \Q3 RTS/CTS to DTE (same as &K3) (default). \R-Ring Indicator Signal Off After Answer This command is supported to ensure compatibility with communications software that issues the \R0 command. \R0 Ring indicator signal is off after the telephone call is answered. \T-Inactivity Timer Use this command to specify the delay time used by the inactivity timer. The delay time is the length of time in minutes that the modem waits during periods of inactivity before disconnecting. Periods of inactivity are defined by no data being sent or received by the DCE. To disable the inactivity timer, use the T0 command. The delay time may also be specified in register S30. This function is only applicable in buffer mode. \T0 Inactivity timer disabled (default). \T1-\T255 Specifies the length of time in minutes that the modem will wait before disconnecting when no data is sent or received. \V-Protocol Result Code Use this command to enable or disable protocol result codes. \V0 Disables protocol result code appended to DCE speed. \V1 Enables protocol result code appended to DCE speed (default). \V2 Enables protocol result code appended to DCE speed (same as \V1). %B-View Numbers in Blacklist If blacklisting is in effect, this command displays the numbers that are currently blacklisted, failed, or delayed. The ERROR result code appears for countries that do not support blacklisting. %C-Data Compression Control Use this command to enable or disable V.42 bis and MNP class 5 data compression. On-line changes do not take effect until a disconnect occurs. %C0 V.42 bis/ MNP 5 disabled. No data compression. 44

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
PCI Modem Card User’s Manual
44
\Q0
Disables flow control (same as
&K
0).
\Q1
XON/XOFF software flow control (same as
&K
4).
\Q3
RTS/CTS to DTE (same as
&K
3) (default).
\R<value>±Ring Indicator Signal Off After Answer
This command is supported to ensure compatibility with communications
software that issues the
\R0
command.
\R0
Ring indicator signal is off after the telephone call is answered.
\T<time delay>±Inactivity Timer
Use this command to specify the delay time used by the inactivity timer. The
delay time is the length of time in minutes that the modem waits during
periods of inactivity before disconnecting. Periods of inactivity are defined
by no data being sent or received by the DCE. To disable the inactivity timer,
use the
T0
command. The delay time may also be specified in register S30.
This function is only applicable in buffer mode.
\T0
Inactivity timer disabled (default).
\T1±\T255
Specifies the length of time in minutes that the modem will
wait before disconnecting when no data is sent or received.
\V<value>±Protocol Result Code
Use this command to enable or disable protocol result codes.
\V0
Disables protocol result code appended to DCE speed.
\V1
Enables protocol result code appended to DCE speed (default).
\V2
Enables protocol result code appended to DCE speed (same as
\V
1).
%B±View Numbers in Blacklist
If blacklisting is in effect, this command displays the numbers that are
currently blacklisted, failed, or delayed. The ERROR result code appears for
countries that do not support blacklisting.
%C<value>±Data Compression Control
Use this command to enable or disable V.42 bis and MNP class 5 data
compression. On-line changes do not take effect until a disconnect occurs.
%C0
V.42 bis/ MNP 5 disabled. No data compression.