Airlink AML001 Manual - Page 57

Selection, Valid <carrier> Values, modulation set by

Get Airlink AML001 PDF manuals and user guides View all Airlink AML001 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

PCI Modem Card User's Manual rate have been determined and before any error control or data compression reports or the final result code (e.g., CONNECT) is transmitted. +MR=0 +MR=1 Enables the modulation report (default). Disables the modulation report. +MS=,,,-Modulation Selection Use this command to set the modem's modulation, the modulation's minimum and maximum transmission rate, and the status of automatic modulation negotiation (automode). The , , and parameters define the modulation and its minimum and maximum rates. The parameter enables or disables automatic modulation negotiation. If a subsequent +MA command is not provided, the automode parameters are constrained by the modulation set by the parameter. The +MA command can further restrict the automatic modulation negotiation settings but it cannot set a modulation that is higher than the modulation set by the +MS command. Valid Values: V92 V.92 (default) V90 V.90 V34 V.34 V32T V.32ter V32B V.32 bis V32 V.32 V22B V.22 bis V. 2 2 V. 2 2 Bell212A Bell 212A* V23C V.23, constant carrier, asymmetric FDM V21 V21 Bell103 Bell 103 Automatic modulation negotiation is enabled or disabled by . However, if a value is specified for the , then automatic rate selection is disabled and the modem will attempt to connect at the specified rate. Valid Values: 0 Disables. 1 Enabled (default). 56

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
PCI Modem Card User’s Manual
56
rate have been determined and before any error control or data compression
reports or the final result code (e.g., CONNECT) is transmitted.
+MR=0
Enables the modulation report (default).
+MR=1
Disables the modulation report.
+MS=<carrier>,<automode>,<min_rate>,<max_rate>±Modulation
Selection
Use this command to set the modem±s modulation, the modulation±s
minimum and maximum transmission rate, and the status of automatic
modulation negotiation (automode). The <carrier>, <min_rate>, and
<max_rate> parameters define the modulation and its minimum and
maximum rates.
The <automode> parameter enables or disables automatic modulation
negotiation. If a subsequent
+MA
command is not provided, the automode
parameters are constrained by the modulation set by the <carrier> parameter.
The
+MA
command can further restrict the automatic modulation
negotiation settings but it cannot set a modulation that is higher than the
modulation set by the
+MS
command.
Valid <carrier> Values:
V92
V.92 (default)
V90
V.90
V34
V.34
V32T
V.32ter
V32B
V.32 bis
V32
V.32
V22B
V.22 bis
V. 2 2
V. 2 2
Bell212A
Bell 212A*
V23C
V.23, constant carrier, asymmetric FDM
V21
V21
Bell103
Bell 103
Automatic modulation negotiation is enabled or disabled by <automode>.
However, if a value is specified for the <max_rate>, then automatic rate
selection is disabled and the modem will attempt to connect at the specified
rate.
Valid <automode> Values:
0
Disables.
1
Enabled (default).