Alpine CDE 102 Cde-102 Owner′s Manual (english) - Page 20

USB Memory Connection (Optional) iPhone/iPod Connect USB memory 1 Open the cover of the USB connection terminal. 2 Connect the USB memory directly to the USB connection terminal, or via the USB cable. (Optional) SOURCE/ Rotary encoder 1 2 45 6 This unit USB Connection Terminal USB memory (Sold Separately) or USB memory Cable (Sold (Sold Separately) Separately) Remove USB memory 1 Carefully, pull out the USB memory from the USB cable or the USB connection terminal. 2 Close the cover of the USB connection terminal. • Change to a source other than the USB memory mode, then remove the USB memory. If the USB memory is removed in the USB memory mode, data may be damaged. • When removing USB memory, pull it out straight. • If sound is not output or USB memory is not recognized even when USB memory is connected, remove USB memory once, then connect it again. • Route the USB cable away from other cables, etc. • After removing the USB memory, close the cover of the USB connection terminal to prevent dust or foreign objects from entering and causing a malfunction. About MP3/WMA/AAC File of USB Memory Playing back MP3/WMA/AAC MP3/WMA/AAC files are prepared, then stored to a USB memory. This unit can recognize at least 100 folders (including root folder) and 100 files per folder stored in USB memory. Playback may not be performed if a USB memory exceeds the limitations described above. Do not make a file's playback time more than 1 hour. Media supported This device can play back USB memory media. Corresponding File Systems This device supports FAT 12/16/32 for USB memory device. 18-EN / /MUTE /ESC /ENT Preset buttons (1 through 6) VIEW An iPhone/iPod can be connected to this unit by using the proprietary ALPINE FULL SPEED™ Connection Cable (KCE-433iV) (sold separately). When this unit is connected by using the cable, the controls on the iPod are not functional. • Set AUX+ SETUP to OFF when an iPhone/iPod is connected (refer to "Setting the AUX+ SETUP Mode" on page 17). • If the Bluetooth INTERFACE (KCE-400BT) and an iPhone/iPod are connected at the same time, be sure to disconnect the iPhone/iPod from the Bluetooth INTERFACE (KCE-400BT) while turning ACC to OFF. • If you connect an iPhone to this unit, it can be used as an iPod. If you use iPhone as a hands-free phone, you need the optional Bluetooth INTERFACE (KCE-400BT). • Internet and telephone functions of iTouch or iPhone, etc., can also be used when connecting to the unit. However, using these functions will stop or pause the playing songs, at this time do not operate the unit to avoid a malfunction. • Do not leave an iPhone/iPod in a car, as its mechanism is sensitive to high temperature and humidity conditions, and damage may result. iPhones/iPods usable with this unit • The unit can be used with the fifth generation and above iPod, iPhone 3G, iPhone, iPod classic, iPod touch, the first generation iPod nano, the second generation iPod nano or the third generation iPod nano only. iPod Shuffle cannot be used, however. • Touch wheel or scroll wheel type iPods without the dock connector cannot be connected to the unit. • The unit can be used with the following iPhones/iPods. iPhone 3G (version 2.0) iPhone (version 1.1.4) iPod touch (version 1.0.4) iPod classic (version 1.1.1) iPod nano (3rd generation) (version 1.1) iPod nano (2nd generation) (version 1.1.3) iPod with video (version 1.2.3) iPod nano (1st generation) (version 1.3.1) • For clarity in identifying your model of iPod, please see Apple's own document "Identifying iPod models" at http://support.apple.com/kb/HT1353 • This unit does not support iPhone/iPod's video playback function, even using a video-compatible cable. • If the unit is used with versions of iTunes earlier than 7.6, correct function and performance are not guaranteed.