Amana NTW4800XQ Installation Instruction - Page 3

Drain System - appliances

Get Amana NTW4800XQ PDF manuals and user guides
UPC - 883049227535
View all Amana NTW4800XQ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

You will need: ■■ A water heater set to 120° F (49° C). ■■ A grounded electrical outlet located within 4 ft. (0.9 m) of power cord on back of washer. ■■ Hot and cold water faucets located within 3 ft. (0.9 m) of hot and cold water fill valves on washer, and water pressure of 5-100 psi (34.5-690 kPa). ■■ A level floor with maximum slope of 1" (25 mm) under entire washer. Installing on carpet is not recommended. ■■ Floor must support washer's total weight (with water and load) of 315 lbs (143 kgs). IMPORTANT: Do not install, store, or operate washer where it will be exposed to weather or in temperatures below 32° F (0° C). Water remaining in washer after use may cause damage in low temperatures. See "Washer Care" in your "Use and Care Guide". Proper installation is your responsibility. Recessed area or closet installation 3" (76 mm) DRAIN SYSTEM Drain system can be installed using a floor drain, wall standpipe, floor standpipe, or laundry tub. Select method you need. IMPORTANT: To avoid siphoning, no more than 4.5" (113 mm) of drain hose should be inside standpipe or below the top of wash tub. Secure drain hose with removable tie strap (A). Floor standpipe drain system 4.5" (113 mm) A 39" (991 mm) Minimum diameter for a standpipe drain: 2" (51 mm). Minimum carry-away capacity: 17 gal. (64 L) per minute. Some standpipes may require a Standpipe Adapter Kit and additional drain hose that may be purchased separately. See "Tools and Parts". Top of standpipe must be at least 39" (991 mm) high; install no higher than 96" (2.4 m) from bottom of washer. Installations higher than 96" (2.4 m) require a sump pump system. Wall standpipe drain system 14" max. (356 mm) 4" (102 mm) 19" (483 mm) 48 in.2 (310 cm2) 24 in.2 (155 cm2) 4.5" (113 mm) A See requirements for floor standpipe drain system. Floor drain system 0" (0 mm) 1" (25 mm) 3" (76 mm) Dimensions show recommended spacing allowed, except for closet door ventilation openings which are minimum required. Consider allowing more space for ease of installation and servicing, spacing for companion appliances and clearances for walls, doors, and floor moldings. Add spacing of 1" (25 mm) on all sides of washer to reduce noise transfer. If a closet door or louvered door is installed, top and bottom air openings in door are required. Floor drain system requires a Siphon Break Kit and additional drain hose that may be purchased separately. See "Tools and Parts". Minimum siphon break: 28" (711 mm) from bottom of washer. (Additional hoses might be needed.) Laundry tub drain system 4.5" (113 mm) A 39" (991 mm) Minimum capacity: 20 gal. (76 L). Top of laundry tub must be at least 39" (991 mm) above floor; install no higher than 96" (2.4 m) from bottom of washer. 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
3
You will need:
A water heater set to 120° F (49° C).
■
A grounded electrical outlet located within 4 ft. (0.9 m)
■
of power cord on back of washer.
Hot and cold water faucets located within 3 ft. (0.9 m)
■
of hot and cold water fill valves on washer, and water
pressure of 5-100 psi (34.5-690 kPa).
A level floor with maximum slope of 1" (25 mm) under entire
■
washer. Installing on carpet is not recommended.
Floor must support washer’s total weight (with water
■
and load) of 315 lbs (143 kgs).
IMPORTANT:
Do not install, store, or operate washer where
it will be exposed to weather or in temperatures below 32° F
(0° C). Water remaining in washer after use may cause
damage in low temperatures. See “Washer Care” in your
“Use and Care Guide”. Proper installation is your responsibility.
Recessed area or closet installation
Dimensions show recommended spacing allowed, except for
closet door ventilation openings which are minimum required.
Consider allowing more space for ease of installation and
servicing, spacing for companion appliances and clearances
for walls, doors, and floor moldings. Add spacing of 1" (25 mm)
on all sides of washer to reduce noise transfer. If a closet door
or louvered door is installed, top and bottom air openings in
door are required.
3"
(76 mm)
3"
(76 mm)
24 in.
2
(155 cm
2
)
48 in.
2
(310 cm
2
)
19"
(483 mm)
1"
(25 mm)
0"
(0 mm)
4"
(102 mm)
14" max.
(356 mm)
DRAIN SYSTEM
Drain system can be installed using a floor drain, wall standpipe,
floor standpipe, or laundry tub. Select method you need.
IMPORTANT:
To avoid siphoning, no more than 4.5" (113 mm)
of drain hose should be inside standpipe or below the top of
wash tub. Secure drain hose with removable tie strap (A).
Minimum diameter for a standpipe drain: 2" (51 mm).
Minimum carry-away capacity: 17 gal. (64 L) per minute.
Some standpipes may require a Standpipe Adapter Kit and
additional drain hose that may be purchased separately. See
“Tools and Parts”. Top of standpipe must be at least 39" (991 mm)
high; install no higher than 96" (2.4 m) from bottom of washer.
Installations higher than 96" (2.4 m) require a sump pump system.
Wall standpipe drain system
Laundry tub drain system
Minimum capacity: 20 gal. (76 L). Top of laundry tub must
be at least 39" (991 mm) above floor; install no higher than
96" (2.4 m) from bottom of washer.
Floor drain system
Floor drain system requires a Siphon Break Kit and additional
drain hose that may be purchased separately. See “Tools and
Parts”. Minimum siphon break: 28" (711 mm) from bottom of
washer. (Additional hoses might be needed.)
Floor standpipe drain system
See requirements for floor standpipe drain system.
4.5"
(113 mm)
39"
(991 mm)
4.5"
(113 mm)
39"
(991 mm)
4.5"
(113 mm)
A
A
A