Ariens Hydro Pro 32 Owners Manual

Ariens Hydro Pro 32 Manual

Get Ariens Hydro Pro 32 PDF manuals and user guides View all Ariens Hydro Pro 32 manuals
Add to My Manuals
Save this manual to your list of manuals

Ariens Hydro Pro 32 manual content summary:

  • Ariens Hydro Pro 32 | Owners Manual - Page 1
    Hydro-Pro Sno-Thro® Owner/Operator Manual Manuel Du Propriétaire/Utilisateur Models 926053 - Hydro Pro 28 (SN 000101 +) 926054 - Hydro Pro 32 (SN 000101 +) 926055 - Hydro Pro 36 (SN 000101 +) 926056 - Hydro Pro 28 Track (SN 000101 +) E10 The use of any gasoline exceeding 10% ethanol (E10) or 10%
  • Ariens Hydro Pro 32 | Owners Manual - Page 2
    SERVICE AND ADJUSTMENTS . . . . . 23 STORAGE 30 SERVICE PARTS 31 ACCESSORIES 31 TROUBLESHOOTING 31 SPECIFICATIONS 33 WARRANTY 34 INTRODUCTION MANUALS Record Engine Model and Serial numbers here. PRODUCT REGISTRATION The Ariens dealer must register the product at the time of purchase.
  • Ariens Hydro Pro 32 | Owners Manual - Page 3
    of unauthorized replacement parts. To locate your nearest Ariens Dealer, go to www.ariens.com on the internet. DISCLAIMER Ariens reserves the right all assembly instructions in this manual. If you do not understand or have difficulty following the instructions, contact your nearest Ariens Dealer for
  • Ariens Hydro Pro 32 | Owners Manual - Page 4
    injury or death. Learn applicable rules and laws in your area. Always follow the practices set forth in this manual. REQUIRED OPERATOR TRAINING Original purchaser of this unit was instructed by the seller on safe and proper operation. If unit is to be used by someone other than original purchaser
  • Ariens Hydro Pro 32 | Owners Manual - Page 5
    your hands. High speed impeller rotates below discharge opening. Wait for all moving parts to stop before removing clogs or servicing. 3. DANGER! Danger! Read Owner/Operator Manual. Wear appropriate hearing protection. ROTATING PARTS. Keep clear of auger while engine is running. • Read Operator
  • Ariens Hydro Pro 32 | Owners Manual - Page 6
    service center. Contact your Ariens Company Equipment Retailer concerning emission controls and component questions. SAFETY RULES Read, understand, and follow all safety practices in Owner/Operator Manual before beginning assembly or operating. Failure to follow instructions rotating parts. Protect
  • Ariens Hydro Pro 32 | Owners Manual - Page 7
    trouble. Striking a foreign object can damage unit. Immediately stop unit and engine. Remove key and wait for all moving parts allow engine to cool before servicing. NEVER fill fuel tank when Maintain or replace safety and instruction labels, as necessary. NEVER . See Engine Manual for proper storage
  • Ariens Hydro Pro 32 | Owners Manual - Page 8
    ASSEMBLY WARNING: AVOID INJURY. Read and understand the entire Safety section before proceeding. WARNING: Dropping or tipping over boxed unit could result in personal injury or damage to unit. PACKAGE CONTENTS IMPORTANT: Be careful not to damage cable spring hooks when rotating handlebars upward.
  • Ariens Hydro Pro 32 | Owners Manual - Page 9
    OS7040 1 2 4 1 3 2 5 7 6 4 7 1 5 3 1. Mounting Holes 2. Discharge Chute 3. Discharge Chute Ring 4. Chute Pedestal 5. Mounting Hardware Figure 5 4. Remove the gear cover from top of chute pedestal. 5. Release the lock teeth on the gear assembly with your finger and rotate the discharge chute so
  • Ariens Hydro Pro 32 | Owners Manual - Page 10
    contact your Dealer for repairs. Check Tire Pressure (926053, 054, 055) Check tire pressure and adjust to the pressure listed on tire sidewall. CAUTION: Avoid injury! Explosive separation of tire and rim parts is possible when they are serviced incorrectly: • Do not attempt to mount a tire without
  • Ariens Hydro Pro 32 | Owners Manual - Page 11
    CONTROLS AND FEATURES 13 11 4 5 12 3 9 2 13 5 10 11 4 14 1 8 3 6 7 9 16 2 12 15 10 14 1 8 7 6 Figure 8 1. Skid Shoes 2. Clean-Out Tool 3. Remote Discharge Chute Deflector 4. Belt Cover 5. Headlight 6. Auger 7. Auger Gearcase 8. Scraper Blade 9. Discharge Chute 10. Impeller 11.
  • Ariens Hydro Pro 32 | Owners Manual - Page 12
    6 3 7 5 8 9 4 10 1 2 4 16 15 14 13 12 11 17 1. Oil Drain 2. Fuel Shut-Off Valve 3. Primer Bulb 4. Recoil Starter Handle 5. Throttle 6. Choke Control Knob 7. Ignition Key 8. Fuel Tank and Cap 9. Oil Fill/Dipstick 10. Electric Starter 11. Attachment Clutch Lever Figure 9 12. Speed Selector
  • Ariens Hydro Pro 32 | Owners Manual - Page 13
    OPERATION WARNING: AVOID INJURY. Read and understand the entire Safety section before proceeding. WARNING: To avoid injury to hands and feet, always disengage clutches, shut off engine, and wait for all movement to stop before unclogging or working on snow thrower. Keep hands and feet away from
  • Ariens Hydro Pro 32 | Owners Manual - Page 14
    -Out Tool The throttle controls the engine speed. To increase or decrease the engine speed, adjust to: 1. Fast (normal or warm starts) 2. Part-Throttle 3. Slow (cold weather starts) Electric Starter The electric starter will start a properly choked and cranked engine when the starter button (120V
  • Ariens Hydro Pro 32 | Owners Manual - Page 15
    maximum traction or unlocked to allow for easier turning. The differential lock knob is located on the right Track Assembly. With the differential locked power is applied equally to both tracks. To engage the differential lock: Pull and turn knob to LOCKED (1) position and release (knob will snap in
  • Ariens Hydro Pro 32 | Owners Manual - Page 16
    blade level with the ground. Refer to Pre-Start on page 18 for recommended settings. Operating Position Figure 14 OS7110 Track Angle (926056) (Figure 15) The track angle can be adjusted to position the auger housing for level clearing, deep cutting or transport. Squeeze the handlebar trigger
  • Ariens Hydro Pro 32 | Owners Manual - Page 17
    is not the same. If the engine experiences starting or performance problems after using a new gasoline, switch to a different fuel provider prevent dirt from entering Fuel Tank. 4. Remove fuel caps. IMPORTANT: Refer to Engine Manual for correct type and grade of fuel. 5. Fill fuel tank to the bottom
  • Ariens Hydro Pro 32 | Owners Manual - Page 18
    to service, both tracks and parts to stop before leaving operator's position. STARTING AND SHUT OFF WARNING: FAILURE TO FOLLOW INSTRUCTIONS could result in personal injury and/or damage to unit. DO NOT attempt to start your unit at this time. Read entire Owner/Operator Manual and the Engine Manual
  • Ariens Hydro Pro 32 | Owners Manual - Page 19
    does not start, refer to TROUBLESHOOTING on page 31.) 11. Adjust choke as needed. 12. Set throttle to Part Throttle or Slow position for warm engine requires less choking than a cold engine. See Engine Manual for detailed instructions. 8. Set throttle to proper starting position. 9. Turn on engine
  • Ariens Hydro Pro 32 | Owners Manual - Page 20
    (see Fuel ShutOff Valve on page 18). 3. Drain fuel tank and fuel system (see Engine Manual for complete instructions). 4. Place unit on a flat level surface. Tip unit forward onto front of auger housing for service. IMPORTANT: Ensure unit is secure and will not tip over. Strap and clamp onto bench
  • Ariens Hydro Pro 32 | Owners Manual - Page 21
    Manual for detailed instructions. CHANGE ENGINE OIL Refer to Engine Manual for detailed instructions. NOTE: Run engine just prior to changing oil, warm oil will flow more freely and carry away more contaminants. CHECK TIRE PRESSURE (926053 only Ariens L3 synthetic severe duty gear lube (Part Number
  • Ariens Hydro Pro 32 | Owners Manual - Page 22
    Ariens Hi-Temp Grease or equivalent to the lubrication fittings. See SERVICE PARTS on page 31. Sno-Thro should be lubricated (Figure 18) at beginning of season or every 25 operating hours. Auger Shaft To grease auger shaft, remove shear bolt nuts and shear bolts per instructions
  • Ariens Hydro Pro 32 | Owners Manual - Page 23
    wear. To adjust scraper blade: 1. Tip unit back onto handlebar, support housing and loosen nuts retaining blade. 2. Reposition scraper blade and tighten Use only Ariens OEM shear bolts for replacement. Use of any other type of shear bolt may result in severe damage to unit. See SERVICE PARTS on page
  • Ariens Hydro Pro 32 | Owners Manual - Page 24
    25. To raise or lower the handlebar: 1. Place unit in service position (see Service Position on page 20). 2. Remove bottom cover. 3. Remove Push deflector remote all the way forward. 2. Loosen adjusting nuts on cable support bracket underneath the dash panel (Figure 22). 3. To adjust the deflector
  • Ariens Hydro Pro 32 | Owners Manual - Page 25
    trunion pin from the bell crank. 3. Start the engine. 4. Hold down the traction clutch paddle. 5. Move bell crank to the position where the wheels/tracks are not moving. 6. Shut off engine. 7. Move speed control to the neutral position and hold in place. 8. Adjust trunion pin to a position where it
  • Ariens Hydro Pro 32 | Owners Manual - Page 26
    the frame. Use a 1/2" (12.7 mm) minimum spacer as a gauge to check the clearance between the roller and the frame. 1. Place the unit into the service position. Remove the bottom cover. 2. With the clutch lever engaged, check the clearance between the frame and plastic roller on the lower end of the
  • Ariens Hydro Pro 32 | Owners Manual - Page 27
    belts and the belt finger. The belt finger should not touch the belts. 1 1 2 Minimum of 1/16" (1.6 mm). 1. Brake Shoe and Pad 2. Attachment Pulley Figure 28 OS7201 2. If there is less than 1/16" (1.6 mm) gap between brake pad and belt, loosen idler adjustment nut, and move idler away from belt
  • Ariens Hydro Pro 32 | Owners Manual - Page 28
    frame and housing. CAUTION: Always support SnoThro frame and blower housing when loosening the cap screws holding them together. Never loosen cap screws while unit is in service position. 9. Remove hex bolts Replace attachment drive belts (see Install new attachment drive belts on page 28). EN - 28
  • Ariens Hydro Pro 32 | Owners Manual - Page 29
    . To adjust (Figure 33): 1. Tighten the adjuster nut to tighten the track tension. Loosen the adjuster nut to reduce track tension. 2. Check that unit tracks straight with no pulling to either side. Track Adjusters Figure 33 OS7228 HEIGHT ADJUSTER CABLE ADJUSTMENT (926056) (Figure 34): 1. Make
  • Ariens Hydro Pro 32 | Owners Manual - Page 30
    on page 20). Touch up all scratched painted surfaces. Remove weight from wheels by putting blocks under frame or axle. FUEL SYSTEM surging to avoid engine damage. 2. Add fuel stabilizer, following the manufacturer's instructions. 3. Turn fuel valve on after adding fuel stabilizer. 4. Re-start engine
  • Ariens Hydro Pro 32 | Owners Manual - Page 31
    Ariens dealer to add the additional accessories available to your Sno-Thro. Part No. Description 72406500 Front Weight Kit 72406900 Slicer Bar 72600300 Composite Skid Shoes 72601500 Cover 72408000 Snow Cab PROBLEM Engine will not crank/start. Engine stops. Engine problems. TROUBLESHOOTING
  • Ariens Hydro Pro 32 | Owners Manual - Page 32
    TROUBLESHOOTING PROBLEM PROBABLE CAUSE CORRECTION Does not operate in Forward / Reverse. 1. Slack in jam nut. 2. Repair or replace traction drive belt. See Traction Drive Belt Replacement on page 28. 3. Adjust speed selector. See Speed Selector Adjustment on page 25. 4. Verify bypass rod is
  • Ariens Hydro Pro 32 | Owners Manual - Page 33
    926053 926054 926055 926056 Description Hydro Pro 28 Hydro Pro 32 Hydro Pro 36 Hydro Pro 28 Track Engine Engine Model Briggs & Stratton Polar Force Pro 2100 Gross Torque* - ft-lbs (N•m) 21.0 (28 (41 x 16.5-20.3) 5.5 (13.97) Track Size and Weight Length - in. (cm) 61.5 (156) Height
  • Ariens Hydro Pro 32 | Owners Manual - Page 34
    ® Utility Vehicles Service (Replacement) Parts Warranty Period Consumer Use 3 Years 3 Years 2 Years Warranty Period Commercial Use 90 Days 1 Year 90 Days 1 Year 1 Year 3 Years 3 Years 1 Year 1 Year 3 Years 90 Days 2 Years 1 Year 90 Days (no labor) 90 Days 1 Year 90 Days (no labor) Special
  • Ariens Hydro Pro 32 | Owners Manual - Page 35
    Register the product immediately at the time of sale. If the dealer does not register the service at owner's expense. • Have the warranty service performed by an authorized Ariens, Gravely, Parker or Countax service representative. To Find an Authorized Service Representative: In the U.S. and Canada
  • Ariens Hydro Pro 32 | Owners Manual - Page 36
    service is limited to service within the area originally distributed. • In countries other than the United States and Canada, contact the Ariens the owner/operator manual. • Modifying the utility vehicle with parts and accessories that are not genuine or authorized Ariens or Gravely parts or
  • Ariens Hydro Pro 32 | Owners Manual - Page 37
    your equipment is defective, the part will be repaired or replaced by Ariens Company. OWNER'S WARRANTY RESPONSIBILITIES: As the small off-road equipment owner, you are responsible for the performance of the required maintenance listed in your Owner's Manual. Ariens Company recommends that you retain
  • Ariens Hydro Pro 32 | Owners Manual - Page 38
    Ariens 655 West Ryan Street Brillion, WI 54110-1072 920-756-4688 www.ariens.com
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
Owner/Operator Manual
Manuel Du Propriétaire/Utilisateur
Hydro-Pro
Sno-Thro
®
04519700A 9/12
Printed in USA
Models
926053 – Hydro Pro 28
(SN 000101 +)
926054 – Hydro Pro 32
(SN 000101 +)
926055 – Hydro Pro 36
(SN 000101 +)
926056 – Hydro Pro 28 Track
(SN 000101 +)
E10
The use of any gasoline exceeding 10% ethanol (E10) or
10% MTBE will void the product warranty.
L’utilisation d’une essence contenant plus de 10% d’éthanol
(E10) ou de 10% de MTBE annulent la garantie.
ENGLISH
FRANÇAIS