Asus MEZ MEZ User Manual - Page 26

Floppy Disk Drive Connector 34-1pin FLOPPY

Get Asus MEZ PDF manuals and user guides View all Asus MEZ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

III. HARDWARE SETUP 9. Primary / Secondary IDE Connectors (Two 40-1pin IDE) These connectors support the provided IDE hard disk ribbon cable. After connecting the single end to the board, connect the two plugs at the other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumper accordingly. Please refer to the documentation of your hard disk for the jumper settings. BIOS now supports SCSI device or IDE CD-ROM bootup (see "HDD Sequence SCSI/IDE First" & "Boot Sequence" in BIOS Features Setup of BIOS SETUP) (Pin 20 is removed to prevent inserting in the wrong orientation when using ribbon cables with pin 20 plugged). TIP: You may configure two hard disks to be both Masters using one ribbon cable on the primary IDE connector and another ribbon cable on the secondary IDE connector. You may install one operating system on an IDE drive and another on a SCSI drive and select the boot disk through BIOS Features Setup. NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1 Secondary IDE (IDE2) Connector Primary IDE (IDE1) Connector 01 01 01 01 01 01 III. H/W SETUP Connectors MEZ IDE Connectors PIN 1 10. Floppy Disk Drive Connector (34-1pin FLOPPY) This connector supports the provided floppy drive ribbon cable. After connecting the single end to the board, connect the two plugs on the other end to the floppy drives. (Pin 5 is removed to prevent inserting in the wrong orientation when using ribbon cables with pin 5 plugged). NOTE: Orient the red markings on the floppy ribbon cable to PIN 1 PIN 1 MEZ Floppy Disk Drive Connector 26 ASUS MEZ User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
26
ASUS MEZ User’s Manual
III. HARDWARE SETUP
Connectors
III.
H/W SETUP
9.
Primary / Secondary IDE Connectors
(Two 40-1pin IDE)
These connectors support the provided IDE hard disk ribbon cable.
After connecting the single end to the board, connect the two plugs at the other
end to your hard disk(s). If you install two hard disks, you must configure the
second drive to Slave mode by setting its jumper accordingly.
Please refer to the
documentation of your hard disk for the jumper settings. BIOS now supports
SCSI device or IDE CD-ROM bootup (see “HDD Sequence SCSI/IDE First” &
“Boot Sequence” in
BIOS Features Setup
of BIOS SETUP)
(Pin 20 is removed
to prevent inserting in the wrong orientation when using ribbon cables with
pin 20 plugged).
TIP:
You may configure two hard disks to be both Masters using one ribbon
cable on the primary IDE connector and another ribbon cable on the secondary
IDE connector. You may install one operating system on an IDE drive and an-
other on a SCSI drive and select the boot disk through BIOS Features Setup.
MEZ IDE Connectors
0
1
0
1
0
1
NOTE:
Orient the red markings
(usually zigzag) on the IDE
ribbon cable to
PIN 1
Primary IDE (IDE1) Connector
Secondary IDE (IDE2) Connector
PIN 1
10. Floppy Disk Drive Connector (34-1pin FLOPPY)
This connector supports the provided floppy drive ribbon cable.
After connect-
ing the single end to the board, connect the two plugs on the other end to the
floppy drives.
(Pin 5 is removed to prevent inserting in the wrong orienta-
tion when using ribbon cables with pin 5 plugged).
NOTE:
Orient the red markings on
the floppy ribbon cable to
PIN 1
MEZ Floppy Disk Drive Connector
PIN 1
0
1
0
1
0
1