Asus P I-P65UP8 CP6ND User Manual - Page 30

ATX Power Switch / Soft Power Switch PWR SW. ATX Power Req.

Page 30 highlights

III. INSTALLATION 13. SMI Suspend Switch Lead (SMI) This allows the user to manually place the system into a suspend mode or "Green" mode where system activity will be instantly decreased to save electricity and expand the life of certain components when the system is not in use. This 2-pin connector (see the figure below) connects to the case-mounted suspend switch. If you do not have a switch for the connector, you may use the "Turbo Switch" since it does not have a function. SMI is activated when it detects a short to open moment and therefore leaving it shorted will not cause any problems. May require one or two pushes depending on the position of the switch. Wake-up can be controlled by settings in the BIOS but the keyboard will always allow wakeup (the SMI lead cannot wake-up the system). If you want to use this connector, "Suspend Switch" in the Power Management Setup of the BIOS SOFTWARE section should be on the default setting of Enable. 14. ATX Power Switch / Soft Power Switch (PWR SW.) (ATX Power Req.) The system power can be controlled by a momentary switch connected to this lead. Pushing the button once will switch the system between ON and OFF. The system power LED shows the status of the system's power. 15. Reset Switch Lead (RESET) This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch This is a preferred method of rebooting in order to prolong the life of the system's power supply. 16. System Power LED (PWR.LED) or (TB.LED) This 3-pin (PWR.LED) or 2-pin (TB.LED) connector connects to the system power LED, which lights when the system is powered on and blinks when it is in sleep (suspend) mode. 17. Keyboard Lock Switch Lead (KEYLOCK) This 2-pin connector connects to the case-mounted key switch to allow keyboard locking. 18. Speaker Connector (SPEAKER) This 4-pin connector connects to the case-mounted speaker. R III. INSTALLATION (Connectors) Power LED SMI Lead ATX Power Switch* Reset SW +5 Volts Ground ExtSMI# Ground PWRBT# Ground ResetCon Ground +5 Volts PLED# KLock# Ground Power LED Keyboard Lock +5 Volts Ground Ground SPKR Speaker Connector * Requires an ATX power supply. System Panel Connectors 30 ASUS P/I-P65UP8 User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40

30
ASUS P/I-P65UP8 User’s Manual
III. INSTALLATION
(Connectors)
III.
INSTALLATION
13. SMI Suspend Switch Lead (SMI)
This allows the user to manually place the system into a suspend mode or “Green”
mode where system activity will be instantly decreased to save electricity and
expand the life of certain components when the system is not in use.
This 2-pin
connector (see the figure below) connects to the case-mounted suspend switch.
If you do not have a switch for the connector, you may use the “Turbo Switch”
since it does not have a function.
SMI is activated when it detects a
short to
open
moment and therefore leaving it shorted will not cause any problems.
May
require one or two pushes depending on the position of the switch.
Wake-up can
be controlled by settings in the BIOS but the keyboard will always allow wake-
up (the SMI lead cannot wake-up the system).
If you want to use this connector,
“Suspend Switch” in the
Power Management Setup
of the BIOS SOFTWARE
section should be on the default setting of
Enable.
14.ATX Power Switch / Soft Power Switch (PWR SW.) (ATX Power Req.)
The system power can be controlled by a momentary switch connected to this
lead.
Pushing the button once will switch the system between ON and OFF.
The system power LED shows the status of the system’s power.
15. Reset Switch Lead (RESET)
This 2-pin connector connects to the case-mounted reset switch for rebooting
your computer without having to turn off your power switch
This is a preferred
method of rebooting in order to prolong the life of the system’s power supply.
16. System Power LED (PWR.LED) or (TB.LED)
This 3-pin (PWR.LED) or 2-pin (TB.LED) connector connects to the system
power LED, which lights when the system is powered on and blinks when it is in
sleep (suspend) mode.
17. Keyboard Lock Switch Lead (KEYLOCK)
This 2-pin connector connects to the case-mounted key switch to allow key-
board locking.
18.
Speaker Connector (SPEAKER)
This 4-pin connector connects to the case-mounted speaker.
System Panel Connectors
PLED#
Ground
PWRBT#
*
Requires an ATX power supply.
KLock#
+5 Volts
SPKR
Keyboard Lock
Speaker
Connector
Power LED
Ground
+5 Volts
Reset SW
SMI Lead
ATX Power
Switch*
ExtSMI#
ResetCon
Ground
Ground
Ground
Ground
+5 Volts
Ground
Power LED