Asus P2-99 P2-99 User Manual - Page 33

ASUS P2-99 User's Manual, Wake-On-LAN Connector 3-pin WOL_CON, IMPORTANT, Wake-On-LAN, IrDA-

Get Asus P2-99 PDF manuals and user guides View all Asus P2-99 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

III. HARDWARE SETUP 11. Wake-On-LAN Connector (3-pin WOL_CON) The WOL_CON connector powers up the system when a wake-up packet or signal is received from the network through the ASUS PCI-L101 LAN card. IMPORTANT: This feature requires that the Wake-On-LAN Power Up Control is set to Enabled (see Power Management Setup under BIOS SETUP) and that your system has an ATX power supply with at least 720mA +5V standby power. Ground +5 Volt Standby (No Connection) III. H/W SETUP Connectors P2-99 P2-99 Wake-On-LAN Connector 12. IrDA-Compliant Infrared Module Connector (5-pin IR) This connector supports the optional wireless transmitting and receiving infrared module. This module mounts to a small opening on system cases that support this feature. You must also configure the setting through "UART2 Use Infrared" in Chipset Features Setup to select whether UART2 is directed for use with COM2 or IrDA. Use the five pins as shown on the Back View and connect a ribbon cable from the module to the motherboard according to the pin definitions. +5V IRRX IRTX Front View Back View (NC) GND P2-99 P2-99 Infrared Module Connector IRTX GND IRRX +5V FIRRX For the infrared feature to be available, you must connect the optional Infrared (IrDA) module to the motherboard ASUS P2-99 User's Manual 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
ASUS P2-99 User’s Manual
33
11.
Wake-On-LAN Connector (3-pin WOL_CON)
The WOL_CON connector powers up the system when a wake-up packet or
signal is received from the network through the ASUS PCI-L101 LAN card.
IMPORTANT:
This feature requires that the
Wake-On-LAN
Power Up Control
is
set to
Enabled
(see
Power Management Setup
under BIOS SETUP) and that your
system has an ATX power supply with at least 720mA +5V standby power.
P2-99 Wake-On-LAN Connector
+5 Volt Standby
(No Connection)
Ground
P2-99
12. IrDA-Compliant Infrared Module Connector (5-pin IR)
This connector supports the optional wireless transmitting and receiving infrared
module. This module mounts to a small opening on system cases that support this
feature. You must also configure the setting through “UART2 Use Infrared” in
Chipset Features Setup
to select whether UART2 is directed for use with COM2
or IrDA. Use the five pins as shown on the Back View and connect a ribbon cable
from the module to the motherboard according to the pin definitions.
Front View
+5V
IRTX
IRRX
FIRRX
GND
Back View
P2-99 Infrared Module Connector
For the infrared feature to be available,
you must connect the optional Infrared
(IrDA) module to the motherboard
P2-99
+5V
IRRX
IRTX
(NC)
GND
III. HARDWARE SETUP
Connectors
III. H/W SETUP