Asus P3-P5G31 User Manual - Page 35

Installing an optical drive

Get Asus P3-P5G31 PDF manuals and user guides View all Asus P3-P5G31 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

2.7 Installing an optical drive The system comes with a 5.25-inch drive bay for an optical drive. If you plan to install an IDE hard disk drive, set the optical drive as a slave device before installing it to the system. Refer to the optical drive documentation for details on how to set the drive as slave device. To install an optical drive: 1. Remove the front panel assembly following the instructions in section "2.3.2 Removing the front panel assembly." 2. Drive a screw on the top right screw hole on both sides of the drive. The screw holes are approximately 5 cm from the drive front panel and 2 cm from the drive base. 2 2 3. Lay the system on its side in a flat and stable surface. 4. Carefully pull the IDE and audio cables and plugs out from the bay until the cables are long enough to connect to the drive. IDE cable and plug Audio cable and plug 5. Connect the IDE cable to the IDE interface at the back of the drive. Match the red stripe on the cable with Pin 1 on the IDE interface. 6. Connect the optical drive audio cable to the 4‑pin connector at the back of the optical drive. The IDE and audio plugs are pre-connected to the primary IDE and internal audio connectors on the motherboard. If you disconnected these plugs, refer to page 4-6 and 4-8 for their respective locations. ASUS P3-P5G31 2-19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
2-19
ASUS P3-P5G31
2.7
Installing an optical drive
The system comes with a 5.25-inch drive bay for an optical drive.
2.
Drive a screw on the top right
screw hole on both sides of
the drive. The screw holes are
approximately 5 cm from the
drive front panel and 2 cm from
the drive base.
2
3.
Lay the system on its side in a flat
and stable surface.
4.
Carefully pull the IDE and audio
cables and plugs out from the bay
until the cables are long enough to
connect to the drive.
Audio cable
and plug
IDE cable
and plug
5.
Connect the IDE cable to the IDE
interface at the back of the drive.
Match the red stripe on the cable
with Pin 1 on the IDE interface.
6.
Connect the optical drive audio
cable to the 4-pin connector at the
back of the optical drive.
To install an optical drive:
1.
Remove the front panel assembly following the instructions in section “2.3.2
Removing the front panel assembly.”
The IDE and audio plugs are pre-connected to the primary IDE and internal
audio connectors on the motherboard. If you disconnected these plugs, refer to
page 4-6 and 4-8 for their respective locations.
If you plan to install an IDE hard disk drive, set the optical drive as a slave
device before installing it to the system. Refer to the optical drive documentation
for details on how to set the drive as slave device.
2