Asus P5VD2 MX P5VD2-MX User's Manual for English Edition - Page 41

Primary/Secondary IDE connectors 40-1 pin PRI_IDE

Get Asus P5VD2 MX - SE Motherboard - Micro ATX PDF manuals and user guides
UPC - 610839154326
View all Asus P5VD2 MX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

2 . Primary/Secondary IDE connectors (40-1 pin PRI_IDE [blue]; 40-1 pin SEC_IDE [black]) The onboard IDE connectors are for Ultra DMA 133/100/66 signal cables. There are three connectors on each Ultra DMA 133/100/66 signal cable: blue, black, and gray. Connect the blue connector to the motherboard's IDE connector, then select one of the following modes to configure your device(s). Single device Two devices Drive jumper setting Cable-Select or Master Cable-Select Master Slave Mode of device(s) Master Slave Master Slave Cable connector Black Black Gray Black or gray • Pin 20 on the IDE connector is removed to match the covered hole on the Ultra DMA cable connector. This prevents incorrect insertion when you connect the IDE cable. • Use the 80-conductor IDE cable for Ultra DMA 100/66 IDE devices. If any device jumper is set as "Cable-Select," make sure all other device jumpers have the same setting. NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1. ® PIN 1 IDE connectors PRI_IDE SEC_IDE ASUS P5VD2-MX/P5V-VM DH 1-29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
ASUS P5VD2-MX/P5V-VM DH
ASUS P5VD2-MX/P5V-VM DH
ASUS P5VD2-MX/P5V-VM DH
ASUS P5VD2-MX/P5V-VM DH
ASUS P5VD2-MX/P5V-VM DH
1-29
1-29
1-29
1-29
1-29
2.
2.
2.
2.
2.
Primary/Secondary IDE connectors (40-1 pin PRI_IDE
Primary/Secondary IDE connectors (40-1 pin PRI_IDE
Primary/Secondary IDE connectors (40-1 pin PRI_IDE
Primary/Secondary IDE connectors (40-1 pin PRI_IDE
Primary/Secondary IDE connectors (40-1 pin PRI_IDE
[blue]; 40-1 pin SEC_IDE [black])
[blue]; 40-1 pin SEC_IDE [black])
[blue]; 40-1 pin SEC_IDE [black])
[blue]; 40-1 pin SEC_IDE [black])
[blue]; 40-1 pin SEC_IDE [black])
The
onboard IDE connectors are for Ultra DMA 133/100/66 signal
cables. There are three
connectors on each Ultra DMA 133/100/66
signal cable: blue, black, and gray. Connect the blue connector to the
motherboard's IDE connector, then select one of the following modes
to configure your device(s).
•
Pin 20 on the IDE connector is removed to match the covered hole
on the Ultra DMA cable connector. This prevents incorrect insertion
when you connect the IDE cable.
•
Use the 80-conductor IDE cable for Ultra DMA 100/66 IDE devices.
Black or gray
Drive jumper
Drive jumper
Drive jumper
Drive jumper
Drive jumper
Mode
Mode
Mode
Mode
Mode
Cable
Cable
Cable
Cable
Cable
setting
setting
setting
setting
setting
of device(s)
of device(s)
of device(s)
of device(s)
of device(s)
connector
connector
connector
connector
connector
Single device
Cable-Select or Master
-
Black
Two devices
Cable-Select
Master
Black
Slave
Gray
Master
Master
Slave
Slave
IDE connectors
NOTE:
Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
SEC_IDE
PIN 1
PRI_IDE
If any device jumper is set
as "Cable-Select,"
make sure all other device
jumpers have the same setting.