Beltronics RX75 Owner's Manual - Page 7
Overview of Programming Options, Details of Programming Options
UPC - 065789230758
View all Beltronics RX75 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 7 highlights
Overview of Programming Options Press the REV button to go from one category to the next PILOT LIGHT (Power-on indication) POWER-ON SEQUENCE SIGNAL STRENGTH METER AUTOMUTE VOICE** CITY MODE SENSITIVITY BRIGHTNESS BANDS * RX75's Factory Default Settings To reset RX75 to its original factory settings, press and hold the "CITY" and "VOL/MUTE" buttons while turning the power on. The RX75's display will provide a "Reset" message, accompanied by an audible alert, acknowledging the reset. **Available only with Optional Speaker Pilot HWY Pilot H Pilot V PwrOn STD PwrOn FST Meter STD Meter THT Meter TEC aMute ON aMute OFF Voice On Voice Off City STD City LoX City NoX Brt AUTO Brt MIN Brt MED Brt MAX Brt DARK Bands ALL Bands MOD Press the CHANGE button to change your setting within a category *Full word: Highway or Auto or City Letter: H or A or C Vehicle voltage *Standard power-on sequence Fast power-on sequence *Standard signal strength meter Threat Display™ TechDisplay *AutoMute on AutoMute off *Voice on Voice off *Standard City mode sensitivity Low X-band sensitivity in City Mode No X-band sensitivity in City Mode *Brightness adjusts automatically Minimum brightness Medium brightness Maximum brightness Dark Mode *All bands enabled One or more bands has been modified Turn bands "ON" or "OFF" by holding down the VOL/MUTE button X ON or OFF K ON or OFF Ka ON or OFF LSR ON or OFF (or BLCK with optional LP904) SWS ON or OFF 10 Details of Programming Options Pilot Light (Power-on indication) Note: When you are using the Dark mode, the display will only show HD, AD, or CD, (Highway-Dark, AutoScan-Dark, or CityDark). PilotHWY (Full description) In this setting, the RX75 will display "Highway," "City," or "AutoScan" as its power-on indication. (factory default) Power-on Sequence PwrOnSTD (Standard) In this setting, each time you turn on the RX75, it will display "BEL PRO," "RX75," "LASER," "Ka-band," "K-band," "X-band," followed by a brief X-band alert. It then confirms communications to all of its components. If a communications error occurs, the appropriate error message will be displayed. (see page 21 for error messages) Pilot H (Letter) In this setting, the RX75 will display "H" for Highway, "C" for City, or "A" for AutoScan. Pilot V (Vehicle voltage) In this setting, the RX75 will display "H" for Highway, "C" for City, and "A" for Auto, and the vehicle's voltage. If the vehicle's voltage drops below 10.5 volts, a low voltage warning will be displayed, followed by an audible alert. A high voltage warning is also given when the vehicle's voltage goes above 16.5 volts. Note: If there is a problem with the front laser receiver or wiring after the initial start-up sequence, the RX75 will briefly display "LsrF ERR." If there is a problem with the rear laser receiver or wiring after the initial start-up sequence, the RX75 will briefly display "LsrR N/A." In both cases, the RX75 will continue to receive radar signals, but will not receive laser signals. If there is a problem with the front radar receiver or wiring after the initial start-up sequence, the RX75 will display "Front N/A," and will then continue to display "Check," "Receiver," "Wiring." The RX75 will not operate in this condition. Please contact your installer if this occurs. PwrOnFST (Fast power-on) This setting shortens RX75's start up sequence to single beep, eliminating the words "BEL PRO," "RX75," "LASER," "Ka-band," "K-band," "X-band," from the start-up sequence. 11