Beltronics STi Driver Owner's Manual - Page 2

Congratulations The BELTRONICS STi DRIVER is the most advanced radar, laser and safety detector ever designed, and is ready to use right out of the box with our recommended factory settings. The STi DRIVER includes full X, K, SuperWide Ka, and Safety Warning System radar capability, front and rear laser detection, dual LNA (low noise amplifier) microwave receivers, digital signal processing (DSP) for superior range and reduced false alarms, our patented Mute and AutoMute, audible and visual band alerts, and all the performance you'd expect from BELTRONICS. In addition, the BELTRONICS STi DRIVER contains the following revolutionary features: • Dual LNA (low noise amplifier) receivers provide the longest possible warning against all radar threats. • TotalShield™ RF Technology provides the ultimate in undetectability. • Programmable Alert Lamp provides additional visual indication of alerts. • Rugged magnesium case provides the ultimate protection for your investment. • High and low voltage warning is given any time the vehicle's voltage drops below 10.5 volts, or goes above 16.5 volts. • Easy-to-use Programming lets you customize up to 9 features. • Exclusive AutoScan mode intelligently reduces unwanted false alarms. • Ultra-bright text-display provides easy to read information from any angle. • Tech Display provides actual numeric radar frequency for any radar signal. • Programmable Bands (on/off). • Detects and decodes up to 64 Safety Warning System messages • Includes new coiled SmartPlug, which provides a convenient mute button right on the plug. If you've used a radar detector before, a review of the Quick Reference Guide on pages 4 and 5, and the Programming information on pages 12 and 13 will briefly explain the new features. If this is your first detector, please read the manual in detail to get the most out of your BELTRONICS STi DRIVER's outstanding performance and innovative features. Please drive safely. FCC Note: Modifications not expressly approved by the manufacturer could void the user's FCC granted authority to operate the equipment. 1 Quick Reference Card ̄ Remove card along perforations ̄ ̄ Remove card along perforations ̄ BELTRONICS STi DRIVER Quick Reference Card There are 9 user-selectable options so you can customize your STi DRIVER for your own preferences. The buttons labeled VOLUME/MUTE and SENS are also used to enter the Programming Mode, REVIEW your current program settings, and to CHANGE any settings as desired. The abbreviations PGM, RVW, and CHG are located on the lower part of the display lens and are highlighted in graphics. How to use Programming 1 To enter Program Mode, press and hold both VOLUME/MUTE and SENS buttons down for 2 seconds. (The unit will beep twice, and will display the word "Program"). 2 Then press the RVW button to review the current settings. (You can either tap the button to change from item to item, or hold the button to scroll through the items). 3 Press the CHG button to change any setting. (You can either tap the button to change from setting to setting, or hold the button to scroll through all the options). 4 To leave Program Mode, simply wait 8 seconds without pressing any button. (The unit will display Complete, beep 4 times, and return to normal operation). Factory Default Settings To reset the STi DRIVER to its original factory settings, press and hold the "VOLUME/MUTE," and "SENS," buttons while turning the power on. The STi DRIVER's display will provide a "Reset" message, accompanied by an audible alert, acknowledging the reset. An example Here is how you would turn the STi DRIVER's AutoMute feature off. 1 Enter the Program Mode by holding both the VOLUME/MUTE and SENS buttons down for 2 seconds. The STi DRIVER will beep twice and display Program. 2 Then hold the RVW button down. The STi DRIVER will scroll through the categories, starting with display (Display), power-on indication ( Pilot), then alert lamp (Alamp), Voice, Power-on sequence, signal strength meter, and then AutoMute. 3 Release the RVW button when the STi DRIVER shows the AutoMute item. Since the factory setting is for AutoMute to be on, the STi DRIVER will display aMute ON. (If you accidentally don't release the Review button in time, and the STi DRIVER goes to the next category, hold the RVW button down again, and scroll through the categories again until aMute is displayed.) 4 Press the CHG button to change from aMute ON to aMute OFF. 5 To complete the Programming, simply wait 8 seconds without pressing any button. The STi DRIVER will display Complete, beep 4 times, and return to normal operation. Programming Details ̈