Beltronics STi Driver Owner's Manual - Page 8

Programming There are 9 user-selectable options so you can customize your STi DRIVER for your own preferences. The buttons labeled VOLUME/MUTE and SENS are also used to enter the Programming Mode, REVIEW your current program settings, and to CHANGE any settings as desired. The words PGM, RVW, and CHG are located on the front of the display lens, and are highlighted in colored graphics. Pages 14-16 explain each option in more detail. How to use Programming 1 To enter Program Mode, press and hold both the VOLUME/MUTE and SENS buttons down for 2 seconds. (The unit will beep twice, and will display the word Program). 2 Then press the RVW button to review the current settings. (You can either tap the button to change from item to item, or hold the button to scroll through the items). 3 Press the CHG button to change any setting. (You can either tap the button to change from setting to setting, or hold the button to scroll through all the options). An example Here is how you would turn STi DRIVER's AutoMute feature off. 1 Enter the Program Mode by holding both the VOLUME/MUTE and SENS buttons down for 2 seconds. The STi DRIVER will beep twice and display Program. 2 Then hold the RVW button down. The STi DRIVER will scroll through the categories, starting with Display (Disp), Pilot (Pilot), Alert Lamp (Alamp), Voice (Voice), Power-on sequence (PwrOn), signal strength meter (Meter), AutoMute (aMute), Brightness (Brt), and Bands (Bands). 3 Release the RVW button when the STi DRIVER shows the AutoMute item. Since the factory setting is for AutoMute to be on, STi DRIVER will display aMute ON. (If you accidentally don't release the RVW button in time, and STi DRIVER goes to the next category, simply hold the RVW button down again, the STi DRIVER will scroll through all of the categories.) 4 Press the CHG button to change from aMute ON to aMute OFF. 4 To leave the Program Mode, simply wait 8 seconds without pressing any button, or press the PWR button. (The unit will display Complete, beep 4 times, and return to normal operation). 5 To complete the Programming, simply wait 8 seconds without pressing any button, or press the PWR button. The STi DRIVER will display Complete, beep 4 times, and return to normal operation. 12 Overview of Programming Press the REVIEW button to go from one category to the next Press the CHANGE button to change your setting within a category DISPLAY Disp STD Disp INV * Standard display Inverted display PILOT (Power-on indication) Pilot HWY Pilot H Pilot V * Full word: Highway, AutoScan, etc. Letter: H, A, C, or Cnx Vehicle voltage ALERT LAMP Alamp ON Alamp OFF * Alert lamp on Alert lamp off VOICE Voice ON Voice OFF * Voice alerts on Voice alerts off POWER-ON SEQUENCE PwrOn STD PwrOn FST * Standard power-on sequence Fast power-on sequence SIGNAL STRENGTH METER Meter STD Meter THT Meter TEC * Standard signal strength meter Threat Display Tech Display AUTOMUTE aMute ON aMute OFF * AutoMute on AutoMute off BRIGHTNESS Brt Auto Brt Min Brt Med Brt Max Brt Dark * Automatic brightness Minimum brightness Medium brightness Maximum brightness All dark BANDS Bands DFT Bands MOD * Factory default settings Factory default settings modified * Factory Default Settings To reset STi DRIVER to its original factory settings, press and hold the "VOLUME/MUTE" and "SENS" buttons while turning the power on. The STi DRIVER's display will provide a "Reset" message, accompanied by an audible alert, acknowledging the reset. Turn bands "ON" or "OFF" by pressing and holding the "SENS" button X ON or OFF (default is on) K ON or OFF (default is on) Ka ON or OFF (default is on) POP ON or OFF (default is off) LSR ON or OFF (default is on) SWS ON or OFF (default is off) 13