BenQ EH600 User Manual - Page 41

Switching to, from an input source, Wireless Connections, PC/YPbPr, Launcher, BenQ Launcher

Get BenQ EH600 PDF manuals and user guides View all BenQ EH600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Switching to BenQ Launcher from an input source When HDMI or PC/YPbPr is selected in the source menu, the projector will exit the BenQ Launcher interface to project video from the input source (e.g. a Blu-Ray/DVD player, set-top box, or PC). The projector will remain outside of the BenQ Launcher interface as long as the HDMI or PC/YPbPr input source is selected or (depending on Auto Source settings) until the projector is powered off and back on again. As a result, anytime the user wants to wirelessly cast their device's screen, view media files stored on a flash drive, or run apps, they must return to the BenQ Launcher interface. To return to BenQ Launcher: 1. Press the source button or the LAUNCHER button on the remote control. 2. Select BenQ Launcher in the source menu. When the Auto Source function is enabled in the Advanced > Settings menu of the projector's OSD menu, the projector will display the BenQ Launcher home screen by default once it is powered on. If the Auto Source function is disabled, the projector will detect if a signal is available from the input source that was last used and switch to that input source if it is available, if a signal is not available or the projector was set to BenQ Launcher during the previous session, the projector will enter the BenQ Launcher home screen. See Settings on page 90. Wireless Connections Connecting the projector to a wireless network Before you can project wirelessly via the projector, you must first connect the projector to a wireless network. To connect your projector to a wireless network, or to switch wireless networks: If you have already connected the projector to a wireless network during the setup wizard you may skip the steps in this section. 1. Install the provided wireless dongle into the wireless dongle port (see Installing the wireless dongle on page 8). 2. Power on the projector (see Starting up the projector on page 22). Operation (under Launcher source) 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
41
Operation (under Launcher source)
Switching to
BenQ Launcher
from an input source
When
HDMI
or
PC/YPbPr
is selected in the source menu, the projector will exit the
BenQ
Launcher
interface to project video from the input source (e.g. a Blu-Ray/DVD player, set-top box, or
PC). The projector will remain outside of the
BenQ Launcher
interface as long as the
HDMI
or
PC/YPbPr
input source is selected or (depending on
Auto Source
settings) until the projector is
powered off and back on again.
As a result, anytime the user wants to wirelessly cast their device’s screen, view media files stored on a
flash drive, or run apps, they must return to the
BenQ Launcher
interface. To return to
BenQ
Launcher
:
1.
Press the source button
or the
LAUNCHER
button on the remote control.
2.
Select
BenQ Launcher
in the source menu.
Wireless Connections
Connecting the projector to a wireless network
Before you can project wirelessly via the projector, you must first connect the projector to a wireless
network. To connect your projector to a wireless network, or to switch wireless networks:
1.
Install the provided wireless dongle into the wireless dongle port (see
Installing the wireless dongle on
page 8
).
2.
Power on the projector (see
Starting up the projector on page 22
).
When the
Auto Source
function is enabled in the
Advanced
>
Settings
menu of the projector’s OSD menu, the
projector will display the
BenQ Launcher
home screen by default once it is powered on. If the
Auto Source
function is disabled, the projector will detect if a signal is available from the input source that was last used and
switch to that input source if it is available, if a signal is not available or the projector was set to
BenQ Launcher
during the previous session, the projector will enter the
BenQ Launcher
home screen. See
Settings on page 90
.
If you have already connected the projector to a wireless network during the setup wizard you may skip the steps in
this section.