BenQ W1210ST User Manual - Page 4

approximately 45 minutes prior to removing the, lamp assembly for replacement. - lamp life

Get BenQ W1210ST PDF manuals and user guides View all BenQ W1210ST manuals
Add to My Manuals
Save this manual to your list of manuals

Page 4 highlights

5. Do not block the vents while the projector is on (even in standby mode). - Do not cover the projector with any item. - Do not place the projector on a blanket, bedding or any other soft surface. 9. Do not look straight into the projector lens during operation. It may harm your sight. 6. In areas where the mains power supply voltage may fluctuate by ±10 volts, it is recommended that you connect the projector through a power stabilizer, surge protector or uninterruptible power supply (UPS) as appropriate to your situation. 10. Do not operate the projector lamp beyond the rated lamp life. Excessive operation of lamps beyond the rated life could cause a lamp to break on rare occasions. 7. Do not step on the projector or place any objects 11. The lamp becomes extremely hot during upon it. operation. Allow the projector to cool for approximately 45 minutes prior to removing the lamp assembly for replacement. 8. Do not place liquids near or on the projector. Liquids spilled into the projector will void your warranty. If the projector does become wet, disconnect it from the power outlet and contact BenQ to have the projector repaired. 12. Never attempt to replace the lamp assembly until the projector has cooled down and is unplugged from the power supply. 4 Important safety instructions

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
4
Important safety instructions
5.
Do not block the vents while the projector is on
(even in standby mode).
- Do not cover the projector with any item.
- Do not place the projector on a blanket,
bedding or any other soft surface.
9.
Do not look straight into the projector lens
during operation. It may harm your sight.
6.
In areas where the mains power supply voltage
may fluctuate by ±10 volts, it is recommended
that you connect the projector through a power
stabilizer, surge protector or uninterruptible
power supply (UPS) as appropriate to your
situation.
10. Do not operate the projector lamp beyond the
rated lamp life. Excessive operation of lamps
beyond the rated life could cause a lamp to break
on rare occasions.
7.
Do not step on the projector or place any objects
upon it.
11. The lamp becomes extremely hot during
operation. Allow the projector to cool for
approximately 45 minutes prior to removing the
lamp assembly for replacement.
8.
Do not place liquids near or on the projector.
Liquids spilled into the projector will void your
warranty. If the projector does become wet,
disconnect it from the power outlet and contact
BenQ to have the projector repaired.
12. Never attempt to replace the lamp assembly until
the projector has cooled down and is unplugged
from the power supply.