BenQ W710ST W700 & W710ST user manual - Page 26

Operation, Starting up the projector - resolution

Get BenQ W710ST PDF manuals and user guides View all BenQ W710ST manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

English Operation Starting up the projector 1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). Check that the POWER indicator light on the projector lights orange after power has been applied. Please use the original accessories (e.g. power cable) only with the device to avoid possible dangers such as electric shock and fire. 2. Press POWER on the projector or remote control to start the projector and a start up tone sounds. The POWER indicator light flashes green and stays green when the projector is on. The start up procedure takes about 30 seconds. In the later stage of start up, a startup logo is projected. (If necessary) Rotate the focus ring to adjust the image clearness. To turn off the ring tone, see "Turning off the Power on/off ring tone" on page 44 for details. If the projector is still hot from previous activity, it will run the cooling fan for approximately 90 seconds before energizing the lamp. 3. To use the OSD menus, please set them to your familiar Please select language language first. See "Personalizing the projector menu display" on page 45 for details. 4. If you are prompted for a password, press the arrow keys to enter a five digit password. See "Utilizing the password function" on page 28 for details. 5. Switch all of the connected equipment on. 6. The projector will start to search for input signals. The Press Enter to confirm, Exit to leave current input signal being scanned displays in the upper left corner of the screen. If the projector doesn't detect a valid signal, the message 'No Signal' will continue displaying until an input signal is found. You can also press SOURCE on the projector or remote control to select your desired input signal. See "Switching input signal" on page 31 for details. If the frequency/resolution of the input signal exceeds the projector's operating range, you will see the message 'Out of Range' displayed on a blank screen. Please change to an input signal which is compatible with the projector's resolution or set the input signal to a lower setting. See "Timing chart" on page 65 for details. To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before turning if off. 26 Operation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
Operation
26
English
Operation
Starting up the projector
1.
Plug the power cord into the projector and
into a wall socket. Turn on the wall socket
switch (where fitted). Check that the
POWER indicator light
on the projector
lights orange after power has been applied.
Please use the original accessories (e.g. power
cable) only with the device to avoid possible
dangers such as electric shock and fire.
2.
Press
POWER
on the projector
or
remote control
to start the projector
and a start up tone sounds. The
POWER
indicator light
flashes green and stays
green when the projector is on.
The start up procedure takes about 30
seconds. In the later stage of start up, a
startup logo is projected.
(If necessary) Rotate the focus ring to
adjust the image clearness.
To turn off the ring tone, see
"Turning off the Power on/off ring tone" on page 44
for details.
If the projector is still hot from previous activity, it will run the cooling fan for approximately 90
seconds before energizing the lamp.
3.
To use the OSD menus, please set them to your familiar
language first. See
"Personalizing the projector menu
display" on page 45
for details.
Please select language
Press Enter to confirm, Exit to leave
4.
If you are prompted for a password, press the arrow keys
to enter a five digit password. See
"Utilizing the
password function" on page 28
for details.
5.
Switch all of the connected equipment on.
6.
The projector will start to search for input signals. The
current input signal being scanned displays in the upper left corner of the screen. If the
projector doesn't detect a valid signal, the message '
No Signal
' will continue displaying
until an input signal is found.
You can also press
SOURCE
on the projector or remote control to select your desired
input signal. See
"Switching input signal" on page 31
for details.
If the frequency/resolution of the input signal exceeds the projector's operating range, you will
see the message 'Out of Range' displayed on a blank screen. Please change to an input signal
which is compatible with the projector's resolution or set the input signal to a lower setting.
See
"Timing chart" on page 65
for details.
To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before turning
if off.