Beretta SV10 Prevail III Beretta SV10 Perennia/Preveil User Manual - Page 20

Routine, Field, Stripping

Get Beretta SV10 Prevail III PDF manuals and user guides View all Beretta SV10 Prevail III manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Pkigfl11 • Move the selector to the second position. (On some models this is not possible since the selector is blocked by a screw.) NOTICE: If the gun features a NON-SELECTIVE SINGLE TRIGGER or a SELECTIVE, BLOCKED TRIGGER (inertia mass type) it is necessary to give a slap to the recoil pad to prepare the firearm to decock the second hammer. • Pull the trigger to decock the second hammer. To remove the snapcaps without recocking the hammers: • Take off the fore-end before you open the gun. • Take out the snapcaps, close the gun and remount the fore-end. ROUTINE FIELD STRIPPING WARNING: Always check that the shotgun is unloaded (empty cartridge chambers). If not, unload it as instructed in the relevant section. WARNING: Never point the firearm at someone or at hard and flat surfaces. Always treat the shotgun as if it were loaded. The routine disassembly is required for cleaning operations every time the gun is fired or before storage in its case. • Completely pull the fore-end catch lever down to detach the fore-end (Fig. 16). • Pull the front of the fore-end down and rotate the fore-end around the hinge pins to remove the fore-end from the barrels (Fig. 16). CAUTION: ONCE THE FORE-END IS DETACHED, DO NOT PULL IT TOO FAR DOWNWARDS BEFORE PULLING IT FORWARD! • Rotate the top lever to the right. • Pivot the barrels in a downward motion, taking care to hold them firmly in order to avoid the risk they accidentally disengage the hinge pins and fall. • Lift the barrels out of the receiver. Disengage Monobloc recesses from hinge pins. The top lever remains open. To store the gun in the supplied guncase: • Remount the fore-end on the barrels and press it to catch the barrel hook. NOTICE: It is advisable to place the top lever in its centered position when the shotgun is being stored or trasnported in a gun case. Proceed as follows: move the top lever completely to the right and at the same time press the top lever plunger (located on the top left section of the breechface of the receiver) Fig 17. Once the top lever plunger is completely depressed, release the top lever to its centered position. 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
Pkigfl11
•
Move
the
selector
to
the
second
position.
(On
some
models
this
is
not
possible
since
the
selector
is
blocked
by
a
screw.)
NOTICE:
If
the
gun
features
a
NON
-SELECTIVE
SINGLE
TRIGGER
or
a
SELECTIVE,
BLOCKED
TRIGGER
(inertia
mass
type)
it
is
necessary
to
give
a
slap
to
the
recoil
pad
to
prepare
the
firearm
to
decock
the
second
hammer.
•
Pull
the
trigger
to
decock
the
second
hammer.
To
remove
the
snapcaps
without
recocking
the
hammers:
•
Take
off
the
fore
-end
before
you
open
the
gun.
•
Take
out
the
snapcaps,
close
the
gun
and
remount
the
fore
-end.
ROUTINE
FIELD
STRIPPING
WARNING:
Always
check
that
the
shotgun
is
unloaded
(empty
cartridge
chambers).
If
not,
unload
it
as
instructed
in
the
relevant
section.
WARNING:
Never
point
the
firearm
at
someone
or
at
hard
and
flat
surfaces.
Always
treat
the
shotgun
as
if
it
were
loaded.
The
routine
disassembly
is
required
for
cleaning
operations
every
time
the
gun
is
fired
or
before
storage
in
its
case.
•
Completely
pull
the
fore
-end
catch
lever
down
to
detach
the
fore
-end
(Fig.
16).
•
Pull
the
front
of
the
fore
-end
down
and
rotate
the
fore
-end
around
the
hinge
pins
to
remove
the
fore
-end
from
the
barrels
(Fig.
16).
CAUTION:
ONCE
THE
FORE
-END
IS
DETACHED,
DO
NOT
PULL
IT
TOO
FAR
DOWNWARDS
BEFORE
PULLING
IT
FORWARD!
•
Rotate
the
top
lever
to
the
right.
•
Pivot
the
barrels
in
a
downward
motion,
taking
care
to
hold
them
firmly
in
order
to
avoid
the
risk
they
accidentally
disengage
the
hinge
pins
and
fall.
•
Lift
the
barrels
out
of
the
receiver.
Disengage
Monobloc
recesses
from
hinge
pins.
The
top
lever
remains
open.
To
store
the
gun
in
the
supplied
guncase:
•
Remount
the
fore
-end
on
the
barrels
and
press
it
to
catch
the
barrel
hook.
NOTICE:
It
is
advisable
to
place
the
top
lever
in
its
centered
position
when
the
shotgun
is
being
stored
or
trasnported
in
a
gun
case.
Proceed
as
follows:
move
the
top
lever
completely
to
the
right
and
at
the
same
time
press
the
top
lever
plunger
(located
on
the
top
left
section
of
the
breechface
of
the
receiver)
Fig
17.
Once
the
top
lever
plunger
is
completely
depressed,
release
the
top
lever
to
its
centered
position.
52