Bernina Bernette 25 Instruction Manual - Page 44

Please Note, Making a buttonhole on stretch fabrics, Basic Sewing Procedures

Get Bernina Bernette 25 PDF manuals and user guides View all Bernina Bernette 25 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Basic Sewing Procedures 43 Raise the presser foot and cut thread. To sew over same buttonhole, raise the presser foot (will return to original position). After sewing the buttonhole stitch, raise the buttonhole lever until it stops. Cut the center of the buttonhole being careful not to cut any stitches on either side. Use a pin as a stopper at the bar tack so you do not cut too much. Making a buttonhole on stretch fabrics When sewing buttonholes on stretch fabric, hook heavy thread or cord under the buttonhole foot. Attach the buttonhole foot and hook the gimp thread onto the back of the presser foot. Bring the two gimp thread ends to the front of the foot and insert them into the grooves, then temporarily tie them there. Lower the presser foot and start sewing. Set the stitch width to match the diameter of the gimp thread. Once sewing is completed, pull the gimp thread gently to remove any slack, then trim off any excess. Please Note: It is suggested that you use interfacing on the backside of the fabric. 502020.75.28_021H2D0101_1010_IM_bernette 20 25_EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Raise the presser foot and cut thread.
To sew over same buttonhole, raise the
presser foot (will return to original position).
After sewing the buttonhole stitch, raise the
buttonhole lever until it stops.
Cut the center of the buttonhole being
careful not to cut any stitches on either side.
Use a pin as a stopper at the bar tack so you
do not cut too much.
When sewing buttonholes on stretch fabric,
hook heavy thread or cord under the button-
hole foot.
Attach the buttonhole foot and hook the
gimp thread onto the back of the presser
foot.
Bring the two gimp thread ends to the front
of the foot and insert them into the grooves,
then temporarily tie them there. Lower the
presser foot and start sewing.
Set the stitch width to match the diameter of
the gimp thread.
Once sewing is completed, pull the gimp
thread gently to remove any slack, then trim
off any excess.
Please Note:
It is suggested that you use interfacing on
the backside of the fabric.
Making a buttonhole on stretch fabrics
Basic Sewing Procedures
43
502020.75.28_021H2D0101_1010_IM_bernette 20 25_EN