Biostar M6VLQ M6VLQ user's manual - Page 54

Init Display First, IDE HDD Block Mode, Onboard FDD Controller

Get Biostar M6VLQ PDF manuals and user guides View all Biostar M6VLQ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Chapter 2 BIOS Setup SB IRQ Select Change the SoundBlaster Pro interrupt signal. The Choices: IRQ5 (default), IRQ7, IRQ9, IRQ10. SB DMA Select Change the SoundBlaster Pro direct memory access setting. The Choices: DMA0, DMA1 (default), DMA2, DMA3. MPU-401 Enable or Disable MPU-401 function. The Choices: Enabled (default), Disabled. MPU-401 I/O Address Change the SoundBlaster Pro MPU-401 I/O address. The Choices: 300-303H, 310-313H, 320-323H, 330-333H (default). Game Port (200-207H) Change the joystick connect port address. The Choices: Enabled (default), Disabled. Init Display First This item allows you to decide to active whether PCI Slot or on-chip VGA first. The Choices: PCI Slot (default), AGP. IDE HDD Block Mode Block mode is also called block transfer, multiple commands, or multiple sector read/ write. If you IDE hard drive supports block mode (most new drives do), select Enabled for automatic detection of the optimal number of block mode (most new drives do), select Enabled for automatic detection of the optimal number of block read/ write per sector the drive can support. The Choices: Enabled (default), Disabled. Onboard FDD Controller Select Enabled if your system has a floppy disk controller (FDC) installed on the system board and you wish to use it. If install and FDC or the system has no floppy drive, select Disabled in this field. The Choices: Enabled (default), Disabled. 2-18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
Chapter 2
BIOS Setup
2-18
SB IRQ Select
Change the SoundBlaster Pro interrupt signal.
The Choices: IRQ5
(default), IRQ7, IRQ9, IRQ10.
SB DMA Select
Change the SoundBlaster Pro direct memory access setting.
The Choices
: DMA0,
DMA1
(default), DMA2, DMA3.
MPU-401
Enable or Disable MPU-401 function.
The Choices: Enabled
(default), Disabled.
MPU-401 I/O Address
Change the SoundBlaster Pro MPU-401 I/O address.
The Choices:
300-303H, 310-313H, 320-323H,
330-333H
(default).
Game Port (200-207H)
Change the joystick connect port address.
The Choices: Enabled
(default), Disabled.
Init Display First
This item allows you to decide to active whether PCI Slot or on-chip VGA first.
The Choices: PCI Slot
(default), AGP.
IDE HDD Block Mode
Block mode is also called block transfer, multiple commands, or multiple sector
read/ write. If you IDE hard drive supports block mode (most new drives do),
select Enabled for automatic detection of the optimal number of block mode
(most new drives do), select Enabled for automatic detection of the optimal
number of block read/ write per sector the drive can support.
The Choices: Enabled
(default), Disabled.
Onboard FDD Controller
Select Enabled if your system has a floppy disk controller (FDC) installed on the
system board and you wish to use it. If install and FDC or the system has no
floppy drive, select Disabled in this field.
The Choices: Enabled
(default), Disabled.