Biostar M6VLQ M6VLQ user's manual - Page 59

Video Off Method, V/H SYNC+Blank, DPMS Support, MODEM Use IRQ, Soft-Off by PWR-BTTN, State After - motherboard manual

Get Biostar M6VLQ PDF manuals and user guides View all Biostar M6VLQ manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Chapter 2 BIOS Setup Video Off Method This option determines the manner in which the monitor is goes blank. V/H SYNC+Blank (default) This selection will cause the system to turn off the vertical and horizontal synchronization ports and write blanks to the video buffer. Blank Screen This option only writes blanks to the video buffer. DPMS Support (default) Initial display power management signaling. MODEM Use IRQ This determines the IRQ, which the MODEM can use. The Choices: 3 (default), 4, 5, 7, 9, 10, 11, NA. Soft-Off by PWR-BTTN Pressing the power button for more than 4 seconds forces the system to enter the Soft-Off state when the system has "hung." The Choices: Delay 4 Sec, Instant-Off (default). 37.5%, 25%, 12.5%. State After Power Failure This field determines the action the system will automatically take when power is restored to a system that had lost power previously without any subsequent manual intervention. There are 3 sources that provide current to the CMOS area that retains these Power-On instructions; the motherboard battery (3V), the Power Supply (5VSB), and the Power Supply (3.3V). While AC is not supplying power, the motherboard uses the motherboard battery (3V). If AC power is supplied and the Power Supply is not turned on, 5VSB from the Power Supply is used. When the Power Supply is eventually turned on 3.3V from the Power Supply will be used. The Choices: Auto (default), On, Off. 2-23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
Chapter 2
BIOS Setup
2-23
Video Off Method
This option determines the manner in which the monitor is goes blank.
V/H SYNC+Blank
(default)
This selection will cause the system to turn off the vertical and
horizontal synchronization ports and write blanks to the video buffer.
Blank Screen
This option only writes blanks to the video buffer.
DPMS Support
(default)
Initial display power management signaling.
MODEM Use IRQ
This determines the IRQ, which the MODEM can use.
The Choices: 3
(default), 4, 5, 7, 9, 10, 11, NA.
Soft-Off by PWR-BTTN
Pressing the power button for more than 4 seconds forces the system to enter the
Soft-Off state when the system has “hung.”
The Choices:
Delay 4 Sec,
Instant-Off
(default).
37.5%, 25%, 12.5%.
State After Power Failure
This field determines the action the system will automatically take when power is
restored to a system that had lost power previously without any subsequent
manual intervention. There are 3 sources that provide current to the CMOS area
that retains these Power-On instructions; the motherboard battery (3V), the Power
Supply (5VSB), and the Power Supply (3.3V). While AC is not supplying power,
the motherboard uses the motherboard battery (3V). If AC power is supplied and
the Power Supply is not turned on, 5VSB from the Power Supply is used. When
the Power Supply is eventually turned on 3.3V from the Power Supply will be
used.
The Choices: Auto
(default), On, Off.