Bissell CleanView Helix Plus Vacuum User Guide - English - Page 10

Warning

Get Bissell CleanView Helix Plus Vacuum PDF manuals and user guides View all Bissell CleanView Helix Plus Vacuum manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Maintenance and care Cleaning the pre-motor filter 1. Unplug the cleaner from electrical outlet. 2. The pre-motor filter protects the motor from debris. It is located underneath the filter cup in the center of the round part of the Lock 'n Seal lever. WARNING: Do not operate cleaner with damp or wet filters or without all filters in place. 3. Remove the small round filter and any debris on top of it. Rinse well under warm water, then air dry thoroughly before replacing. Pre-Motor Filter Replacing the post-motor filter Use only genuine BISSELL style 9 (#32076) replacement filters in your BISSELL CleanView Helix. 1. Unplug the cleaner from electrical outlet. 2. The post-motor filter assists in the filtration process to return clean air to the room. It is located behind the door on the side of the vacuum. When the filter becomes dirty, open the door, remove the filter and replace. The white, pleated HEPA Media Filter* is not washable. Note: A basic washable post-motor filter with reduced filtration is available if desired. Post-Motor Filter WARNING: To reduce the risk of injury from moving parts, turn off vacuum cleaner and disconnect Power Plug from electrical outlet. Checking rotating floor brush and drive belt You should check your vacuum cleaner's rotating floor brush and drive belt regularly for wear or damage. You 3. should also clean the brush and brush ends of strings, hair and carpet fibers. These can wrap around the brush and hamper its ability to effectively clean your carpet. Also remove any debris that has accumulated under the brush cover. 1. Unplug cleaner from electrical outlet. 2. Place handle in low position and turn Motor Pulley vacuum cleaner over so bottom side is up. 3. Remove the five screws with a Phillips 4. head screwdriver. Lift the brush cover off. 4. Grasp rotating floor brush at both ends and lift. *The filter media, not the vacuum as a whole, complies with IEST-RP-CC001.5 HEPA standard. Brush Cover 10 w w w. b i s s e l l . c o m 800.237.7691

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
www.bissell.com
800.237.7691
M
aintenance and care
10
Cleaning the pre-motor filter
1.
Unplug the cleaner from electrical outlet.
2.
The pre-motor filter protects the motor
from debris. It is located underneath the
filter cup in the center of the round part
of the Lock ‘n Seal lever.
3.
Remove the small round filter and any
debris on top of it. Rinse well under
warm water, then air dry thoroughly
before replacing.
Replacing the post-motor filter
Use only genuine BISSELL style 9
(#32076) replacement filters in your
BISSELL CleanView Helix.
1.
Unplug the cleaner from electrical outlet.
2.
The post-motor filter assists in the filtration
process to return clean air to the room.
It is located behind the door on the side
of the vacuum. When the filter becomes
dirty, open the door, remove the filter and
replace. The white, pleated HEPA Media
Filter* is not washable.
Note: A basic washable
post-motor filter with reduced
filtration is available if desired.
You should check your vacuum cleaner’s
rotating floor brush and drive belt
regularly for wear or damage. You
should also clean the brush and brush
ends of strings, hair and carpet fibers.
These can wrap around the brush and
hamper its ability to effectively clean
your carpet. Also remove any debris
that has accumulated under the
brush cover.
1.
Unplug cleaner from electrical outlet.
2.
Place handle in low position and turn
vacuum cleaner over so bottom side is up.
3.
Remove the five screws with a Phillips
head screwdriver. Lift the brush cover off.
4.
Grasp rotating floor brush at both ends and lift.
Post-Motor
Filter
WARNING:
Do not operate cleaner
with damp or wet filters or
without all filters in place.
WARNING:
To reduce the risk of injury from
moving parts, turn off vacuum
cleaner and disconnect Power
Plug from electrical outlet.
Pre-Motor
Filter
Motor Pulley
4.
Checking rotating floor brush and drive belt
3.
Brush Cover
*The filter media, not the vacuum as a whole,
complies with IEST-RP-CC001.5 HEPA standard.