Bosch B36IB70NSP Installation Instructions - Page 18

Important, Caution

Get Bosch B36IB70NSP PDF manuals and user guides View all Bosch B36IB70NSP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

7. Attaching an alternative antiĆtip device ! IMPORTANT NOTE ! If possible, always screw the wooden beam to existing studs on the rear panel of the cavity. If the antiĆtip brackets cannot be attached securely, an alternative antiĆtip device can be attached. However, ensure that there is no play between the appliance and the antiĆtip device. q Saw the wooden beam (cross section min. 3" x 4" (75 cmx 100 cm)) to the required length. Length is equal to the width of the installation cavity! i Note - If the installation cavity is deeper than the appliance, select a beam which has a larger cross section or attach 2 beams. - The beam must cover the appliance by at least 2" (50.8 mm). q Locate wall studs near the rear panel of the cavity and mark drill holes in the beam. q Predrill the wooden beam. q Attach the wooden beam to the rear panel of the cavity. 8. Preparing to connect the water (only for appliances which require a water connection) See also Connecting the water". d CAUTION d Turn off the main water tap to prevent damage caused by leaking water. q Attach the connecting pipe to the shutĆoff valve according to the instructions supplied by the manufacturer of the ice maker installation kit. q Install the connecting pipe. Always observe the indicated gap dimensions to prevent damage to the connecting pipe when pushing in the appliance. q Attach the connecting pipe to the floor with adhesive tape. q Mark the installation height (lower edge of the beam) on the rear panel of the cavity. q Select screws according to the thickness of the wooden beam: length = min. 2.5 x beam thickness, diameter #12 or #14. i Specify the number of screws according to the cavity width, thereby ensuring that the beam can be attached securely. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
18
7.
Attaching
an alternative
antiĆtip
device
!
IMPORTANT
NOTE
!
If
possible,
always
screw
the
wooden
beam
to
existing
studs
on
the rear
panel of
the
cavity.
If the
antiĆtip brackets cannot
be
attached
securely,
an±alternative
antiĆtip device
can
be
attached.
However,
ensure
that there
is
no
play between
the
appliance
and the
antiĆtip
device.
q
Saw
the
wooden
beam
(cross
section
min.
3" x 4"
(75 ±cmx
100
cm)) to
the
required
length.
Length
is
equal to the
width
of
the
installation cavity!
i
Note
-
If the
installation
cavity is
deeper
than
the
appliance,
select
a
beam which
has
a
larger
cross
section or
attach
2
beams.
-
The beam must
cover
the
appliance
by at
least 2"
(50.8
mm).
q
Mark
the
installation
height
(lower
edge
of
the beam)
on the
rear panel of
the
cavity.
q
Select
screws
according
to
the
thickness
of
the
wooden
beam:
length
= min.
2.5
x
beam
thickness,
diameter #12
or #14.
i
Specify the
number
of
screws
according
to
the
cavity width,
thereby ensuring
that
the
beam can
be±attached securely.
q
Locate wall studs
near
the rear
panel of
the
cavity
and
mark
drill holes in the beam.
q
Predrill the wooden beam.
q
Attach the wooden beam
to
the rear
panel
of
the
cavity.
8.
Preparing to connect the
water
(only for
appliances which require a water
connection)
See also
²Connecting
the water".
d
CAUTION
d
Turn off
the main water
tap
to
prevent damage
caused
by
leaking
water.
q
Attach the connecting
pipe to
the shutĆoff
valve
according
to
the instructions supplied by the
manufacturer
of
the ice maker
installation
kit.
q
Install the connecting
pipe. Always
observe
the
indicated
gap
dimensions
to
prevent damage
to the
connecting
pipe when pushing
in the appliance.
q
Attach the connecting
pipe to
the floor with
adhesive tape.