Bosch B36IB70NSP Installation Instructions - Page 7

Installation, location

Get Bosch B36IB70NSP PDF manuals and user guides View all Bosch B36IB70NSP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Installation location1. d WARNING d Do not install the appliance: - outdoors, - in an environment with dripping water, - in rooms which are at risk of frost. Appliance is very heavy ć for empty weight see the following table: Bottom Freezer 36" approx. 430 lbs / 195 kg Installation room The appliance should be installed in a dry, ventilated room. The ambient temperature should not drop below 55 °F (13 °C) or rise above 110 °F (43 °C), otherwise malfunctions may occur. The installation location should not be exposed to direct sunlight and not placed near a heat source, such as an oven, radiator, etc. If installation next to a heat source is unavoidable, use a suitable insulating plate or observe the following minimum distances from the heat source: - 11/4" (30 mm) from an electric cooker, - 12" (300 mm) from an oil or solidĆfuel cooker. Installation cavity It is important to observe the specified dimensions of the installation cavity for a troubleĆfree installation of the appliance and for the subsequent general view of the furniture front. i In particular ensure that the cavity is square. Squareness can be checked by suitable means, e.g. spirit level, diagonal measurements, etc. i The side walls of the cavity must be flush. The minimum thickness of side walls and the top wall must be 5/8" (16 mm). The minimum thickness of toe kick panel must be 1/2" (13 mm). A thickness of 3/4" (19 mm) is recommended. Furniture/fixtures The new appliance is screwed securely to adjacent and overhead furniture/fixtures. For this reason it is essential that all attachable furniture/fixtures are connected securely to the base or the wall by suitable means. Base d WARNING d A fullyĆload appliance is very heavy ć for the loadĆbearing capacity at least see the following table: Bottom Freezer 36" approx. 1200 lbs / 540 kg To ensure that the appliance is installed securely and functions properly, the base must be flat and level. The base must be made of a hard, rigid material. The installation area must be the same height as the rest of the room. On account of the heavy weight of a fully loaded appliance, a loadĆbearing base is required. If in doubt, contact an architect or a building expert. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
7
Installation
location
1.
d
WARNING
d
Do not
install the
appliance:
-
outdoors,
-
in an
environment with
dripping
water,
-
in rooms
which
are at
risk
of
frost.
Appliance
is
very heavy ć
for
empty weight
see
the
following
table:
Bottom
Freezer 36"
approx.
430
lbs
/
195
kg
Installation room
The appliance
should be
installed
in
a
dry,
ventilated
room.
The
ambient
temperature
should
not
drop
below
55
°
F
(13
°
C)
or rise
above
110
°
F
(43
°
C),
otherwise
malfunctions
may
occur.
The
installation
location
should
not
be
exposed
to
direct
sunlight and not
placed
near
a
heat
source,
such
as an
oven,
radiator,
etc.
If
installation
next
to
a
heat
source is
unavoidable,
use
a
suitable
insulating
plate
or
observe
the
following
minimum distances
from
the
heat
source:
-
1
1
/
4
"
(30
mm)
from
an
electric
cooker,
-
12"
(300
mm)
from
an
oil or
solidĆfuel cooker.
Installation cavity
It is
important
to
observe
the
specified
dimensions
of
the±installation
cavity for
a
troubleĆfree
installation of
the
appliance
and for the
subsequent
general view
of
the
furniture front.
i
In particular ensure
that
the
cavity is
square.
Squareness
can
be
checked
by suitable
means,
e.g.±spirit
level,
diagonal measurements,
etc.
i
The side walls
of
the cavity
must be flush.
The minimum
thickness of
side walls
and
the
top wall
must be
5
/
8
" (16
mm).
The minimum
thickness of
toe kick
panel must
be
1
/
2
"±(13
mm).
A
thickness of
3
/
4
" (19
mm)
is
recommended.
Furniture/fixtures
The new
appliance is screwed
securely
to adjacent
and±overhead
furniture/fixtures.
For
this
reason it is
essential that all attachable
furniture/fixtures
are connected
securely
to the
base±or±the wall by
suitable means.
Base
d
WARNING
d
A
fullyĆload
appliance is very
heavy
ć
for
the
loadĆbearing±capacity
at least see the following table:
Bottom
Freezer
36"
approx. 1200 lbs / 540 kg
To
ensure that the appliance is installed
securely and
functions properly, the base must be flat and level.
The base must be made of
a hard, rigid
material.
The installation area must be the same height
as the
rest
of
the room.
On
account of
the heavy
weight of
a fully
loaded
appliance, a loadĆbearing
base is required.
If
in
doubt,
contact an architect or
a building
expert.