Brother International BAS-342G PS Instruction Manual - English - Page 71

Replacing the movable and fixed knives, accessory spacers t=0.2

Get Brother International BAS-342G PS PDF manuals and user guides View all Brother International BAS-342G PS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

11-10. Replacing the movable and fixed knives 11. STANDARD ADJUSTMENTS 2771B 1. Loosen the two bolts (1) and then remove the feed plate (2). 2. Open the shuttle race cover, remove the two screws (3) and the two flat screws (4), and then remove the needle plate (5). 3. Remove the movable knife (6) and the fixed knife (7). 1890B 2772B 4. Install the new fixed knife (7) in the position shown in the illustration. 5. Apply grease to the outside of the collar (8) and to the shoulder screw (9), and then install the new movable knife (6) together with the thrust washer (10) and the movable knife spacer (11). 6. Check that the movable knife (6) and fixed knife (7) cut the thread cleanly. Replace the movable knife spacer with accessory spacers (t=0.2, 0.3, 0.4) so that the knives trim the thread accurately. * If the knife pressure is too weak and the thread is not completely cut, use a thinner movable knife spacer. * If the knife pressure is too strong and the movable knife (6) turns stiffly, use a thicker movable knife spacer. 7. Apply grease to the pin (12), place it into the movable knife connecting plate (13), and install it to the needle plate (5). 8. Check that the needle is aligned with the center of the needle hole. BAS-342G PS 62

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
11. STANDARD ADJUSTMENTS
BAS-342G PS
62
11-10. Replacing the movable and fixed knives
1. Loosen the two bolts (1) and then remove the feed plate (2).
2. Open the shuttle race cover, remove the two screws (3) and the two flat screws (4), and then remove the needle plate (5).
3. Remove the movable knife (6) and the fixed knife (7).
4. Install the new fixed knife (7) in the position shown in the illustration.
5. Apply grease to the outside of the collar (8) and to the shoulder screw (9), and then install the new movable knife (6)
together with the thrust washer (10) and the movable knife spacer (11).
6. Check that the movable knife (6) and fixed knife (7) cut the thread cleanly. Replace the movable knife spacer with
accessory spacers (t=0.2, 0.3, 0.4) so that the knives trim the thread accurately.
* If the knife pressure is too weak and the thread is not completely cut, use a thinner movable knife spacer.
* If the knife pressure is too strong and the movable knife (6) turns stiffly, use a thicker movable knife spacer.
7. Apply grease to the pin (12), place it into the movable knife connecting plate (13), and install it to the needle plate (5).
8. Check that the needle is aligned with the center of the needle hole.
2771B
2772B
1890B