Home » Brother International Manuals » Sewing Machines » Brother International BAS-342G PS » Manual Viewer

Brother International BAS-342G PS Instruction Manual - English - Page 73

Presser foot installation position, 11-13. Changing the intermittent stroke

Get Brother International BAS-342G PS PDF manuals and user guides

View all Brother International BAS-342G PS manuals

Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

11. STANDARD ADJUSTMENTS 11-12. Presser foot installation position Install the intermittent presser foot (1) with the screw (2) so that the distance from the bottom of the intermittent presser foot to the top of the needle plate is 19.5 mm when the sewing machine is stopped and the intermittent presser foot (1) is raised. 1894B 11-13. Changing the intermittent stroke The intermittent stroke can be adjusted to within 2 − 10 mm by adjusting the position of the stepping clamp connecting rod and changing the installation position of stepping clamp link A. 4049M 1. Remove the face plate. 2. Remove the two screws (1) and the two shoulder screws (2), and then remove stepping clamp link A (3). 3. Change the installation position for stepping clamp link A (3) to either A, B or C above. If the position of the stepping clamp connecting rod is adjusted as described in the following at any one of the installation positions, the adjustment range for the intermittent stroke will as given in the following table. (Refer to the next page.) Installation position Intermittent stroke range A 2 − 4.5mm B 4.5 − 10mm C 0 mm (Presser foot does not move up and down) 5012Q BAS-342G PS 64

Section	Page
COVER	1
SAFETY INSTRUCTIONS	3
[1] Safety indications and their meanings	3
[2] Notes on safety	4
[3] Warning labels	6
CONTENTS	8
1. NAMES OF MAJOR PARTS	10
2. SPECIFICATIONS	11
3. TABLE PROCESSING DIAGRAM	12
4. INSTALLATION	13
4-1. Removing the machine head fixing bolts [1]	13
4-2. Installing the control box [2]	14
4-3. Installing the oil pan and support lever base	15
4-4. Installing the machine head	15
4-5. Tilting back and returning the machine head	16
4-6. Installing the gas spring	17
4-7. Installing the operation panel [3]	18
4-8. Installing the solenoid valve assembly	19
4-9. Connecting the air tubes [4]	19
4-10. Installing the air hose [5]	19
4-11. Adjusting the air pressure [6]	20
4-12. Adjusting the speed controller [7]	20
4-13. Connecting the cords [8]	21
4-14. Connecting the ground wire [9]	23
4-15. Securing the cords and air tubes [10]	24
4-16. Installing the eye guard [11]	25
4-17. Installing the cotton stand [12]	25
4-18. Lubrication [13]	26
4-19. Connecting the power cord [14]	27
4-20. Checking the safety switch [15]	27
5. PREPARATION BEFORE SEWING	28
5-1. Installing the needle	28
5-2. Operating the 2-pedal foot switch	28
5-3. Threading the upper thread	29
5-4. Winding the lower thread	31
5-5. Installing the bobbin case	32
5-6. Thread tension	33
5-6-1. Lower thread tension	33
5-6-2. Upper thread tension	33
5-7. Home position detection	34
5-8. Setting 2-step operation for the work clamp	35
6. USING THE OPERATION PANEL (BASIC OPERATIONS)	36
6-1. Name and function of each operation panel item	36
6-2. Loading sewing data	38
6-3. Setting the program number	38
6-4. Setting the X-scale and Y-scale	39
6-5. Setting the sewing speed	39
6-6. Checking the sewing pattern	40
6-7. Setting the height of the intermittent presser foot	41
7. USING THE OPERATION PANEL (ADVANCED OPERATIONS)	42
7-1. List of advanced functions	42
7-2. Setting memory switches	43
7-3. List of memory switch settings	44
7-4. Using the lower thread counter	45
7-5. Using the production counter	46
7-6. Setting the split number	47
7-7. Using user programs	48
7-8. Using cycle programs	51
7-9. Direct selection (combination table)	53
7-10. X and Y parallel movement of sewing pattern	54
7-11. Clearing memory data (reinitialization)	55
8. USING CF CARDS	56
8-1. Notes on handling CF cards (sold separately)	56
8-2. Structure of a CF card folder	56
8-3. Data read/write mode	57
8-3-1. Reading all sewing data from the CF card at once	58
8-3-2. Writing all sewing data to the CF card at once	59
9. SEWING	60
9-1. Sewing	60
9-2. Using the STOP switch	61
9-3. Using the thread wiper switch	61
10. CLEANING	62
10-1. Cleaning the rotary hook	62
10-2. Draining the oil	62
10-3. Checking the regulator	62
10-4. Cleaning the control box air inlet ports	63
10-5. Cleaning the eye guard	63
10-6. Checking the needle	63
10-7. Lubrication	63
11. STANDARD ADJUSTMENTS	64
11-1. Adjusting the thread take-up spring	64
11-2. Adjusting arm thread guide R	65
11-3. Adjusting the needle bar height	65
11-4. Adjusting the needle bar lift amount	66
11-5. Adjusting the driver needle guard	66
11-6. Adjusting the needle clearance	67
11-7. Adjusting the inner rotary hook and hook stopper overlap	67
11-8. Adjusting the rotary hook lubrication amount	67
11-9. Adjusting the position of the movable knife	68
11-10. Replacing the movable and fixed knives	71
11-10-1. Installing the feed plate	72
11-11. Adjusting the thread wiper	72
11-12. Presser foot installation position	73
11-13. Changing the intermittent stroke	73
11-14. Adjusting the work clamp lift amount	75
11-15. Adjusting the air pressure	75
12. TABLE OF ERROR CODES	76
13. TROUBLESHOOTING	80
14. 7-SEGMENT DISPLAY	84