Brother International BES-916AC Instruction Manual - English - Page 31

The X and Y, a buzzer sounds three times.

Get Brother International BES-916AC PDF manuals and user guides View all Brother International BES-916AC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Chapter 1 Preparation of Embroidery Machine When the machine is turned on: The message "Needle case lock" may appear while a buzzer sounds intermittently. In such a case, the machine is not ready to start because the needle bar case is not positioned correctly, and thus the needles are not in proper alignment with the holes of the needle plates. Follow the steps below to fix this. 1. Check if the needles stop in the normal w position. When cam plate w is raised, it is in the automatic jump position. This is the normal position. BES-916AC BES-1216AC e 2. Turn knob e slowly. If knob e cannot be turned or is too heavy to rotate, thread take-up q or the needle bar is not in the normal position. Check if any obstacle interferes with the needle end or the presser foot. Note) Do not turn the knob forcibly. 3. There is a dead zone in which the needle bar case cannot be moved even by turning knob e. Turn the knob to the normal position in the vicinity of the center of the dead zone. e 4. Press . STOP 5. The message "Moving frame" appears and a buzzer sounds three times. The X and Y carriages move automatically so as to bring the hoop center to the home position or to the position where it was located at the end of the previous operation. 6. The main menu appears. BES-916AC • BES-1216AC 29

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
Chapter 1
Preparation of Embroidery Machine
BES-916AC • BES-1216AC
29
w
BES-916AC
BES-1216AC
e
e
When the machine is turned on:
The message "Needle case lock" may appear while a buzzer sounds intermittently.
In such a
case, the machine is not ready to start because the needle bar case is not positioned correctly,
and thus the needles are not in proper alignment with the holes of the needle plates.
Follow
the steps below to fix this.
1.
Check if the needles stop in the normal
position.
When cam plate
w
is raised, it is in the automatic jump
position.
This is the normal position.
2.
Turn knob
e
slowly.
If knob
e
cannot be turned or is too heavy to rotate,
thread take-up
q
or the needle bar is not in the normal
position.
Check if any obstacle interferes with the needle
end or the presser foot.
Note)
Do not turn the knob forcibly.
3.
There is a dead zone in which the needle
bar case cannot be moved even by turning
knob
e
.
Turn the knob to the normal
position in the vicinity of the center of the
dead zone.
4.
Press
STOP
.
5.
The message "Moving frame" appears and
a buzzer sounds three times.
The X and Y
carriages move automatically so as to bring
the hoop center to the home position or to
the position where it was located at the end
of the previous operation.
6.
The main menu appears.