Brother International BES-916AC Instruction Manual - English - Page 32

carriages move automatically so as to bring, the hoop center to the home position or

Get Brother International BES-916AC PDF manuals and user guides View all Brother International BES-916AC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Chapter 1 Preparation of Embroidery Machine If the machine is not ready to operate because the needle bars in the drive position are out of the normal position, the message "Needle stop position error" appears. Follow the steps below if this occurs. 1. Set "100° ( )" on the pulley to "STOP POSITION." 2. Press . STOP Note) Check if the needle bars are lowered. If so, return them to the normal stop position. (Refer to "Normal needle stop position" on page 30.) 3. The message "Moving frame" appears and a buzzer sounds four times. The X and Y carriages move automatically so as to bring the hoop center to the home position or to the position where it was located at the end of the previous operation. 4. The main menu appears. Normal needle stop position y t Viewing the inside through the clearance, each needle bar is in the jump position at the top (as shown in the figure) and needle bar vertical piece t lowers to keep it from contact with needle bar clamp y. (The thread take-ups are aligned horizontally.) t 30 Note) When the power switch has been turned on or when restarting embroidering while the machine is stopped or suspended, be sure to return the needles to the normal stop position. • Align all thread take-ups horizontally. • If the needle bar in the embroidering posi- tion is lowered with needle bar vertical piece t, separate them in the following manner. For safety, insert a tool such as a y screwdriver into the clearance at the front left side of the needle bar case and turn the needle bar vertical piece t by pushing its end. When the needle bar and the needle bar vertical piece are separated, the needle bar is raised to the top by the spring. BES-916AC • BES-1216AC

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
Chapter 1
Preparation of Embroidery Machine
BES-916AC • BES-1216AC
30
If the machine is not ready to operate because the needle bars in the drive position are out of
the normal position, the message "Needle stop position error" appears.
Follow the steps
below if this occurs.
1.
Set "100
°
(
)" on the pulley to "STOP
POSITION."
2.
Press
STOP
.
Note)
Check if the needle bars are lowered.
If so,
return them to the normal stop position. (Re-
fer to "Normal needle stop position" on page
30.)
3.
The message "Moving frame" appears and
a buzzer sounds four times.
The X and Y
carriages move automatically so as to bring
the hoop center to the home position or to
the position where it was located at the end
of the previous operation.
4.
The main menu appears.
Normal needle stop position
y
t
y
t
Viewing the inside through the clearance,
each needle bar is in the jump position at
the top (as shown in the figure) and needle
bar vertical piece
t
lowers to keep it from
contact with needle bar clamp
y
.
(The
thread take-ups are aligned horizontally.)
Note)
When the power switch has been turned on
or when restarting embroidering while the
machine is stopped or suspended, be sure to
return the needles to the normal stop posi-
tion.
•
Align all thread take-ups horizontally.
•
If the needle bar in the embroidering posi-
tion is lowered with needle bar vertical
piece
t
, separate them in the following
manner.
For safety, insert a tool such as a
screwdriver into the clearance at the front
left side of the needle bar case and turn the
needle bar vertical piece
t
by pushing its
end.
When the needle bar and the needle
bar vertical piece are separated, the needle
bar is raised to the top by the spring.