Home » Brother International Manuals » Laser Printers » Brother International HL 5370DW » Manual Viewer

Brother International HL 5370DW Network Users Manual - English - Page 102

on You have completed the wireless setup. To install the printer driver, Go to step - drum error

UPC - 012502622482

View all Brother International HL 5370DW manuals

Add to My Manuals
Save this manual to your list of manuals

Page 102 highlights

Wireless configuration using the one-push wireless setting mode (For HL-5370DW) f Wait until the Status LED of your machine indicates Connected. The Status LED will turn on for 5 minutes. (See the table below) This indication means the machine has successfully connected to your access point/router. You can now use your machine in a wireless network. If the LED indicates Connection Fail (See the table below), the machine has not successfully connected to your access point/router. Try starting from c again. If the same message is indicated again, reset the print server back to its factory default settings and try again. For resetting, see Reset the network settings to the factory default on page 118. If the LED indicates No Access Point (See the table below), the machine has detected no access point/router on your network. Make sure you place the Brother machine as close to the network access point/router as possible with minimal obstructions, and try starting from c again. If the same message is indicated again, reset the print server back to its factory default settings and try again. For resetting, see Reset the network settings to the factory default on page 118. If the LED indicates Connection Error (See the table below), the machine has detected more than 6 2 access points/routers on your network that have the SecureEasySetup™, the Wi-Fi Protected Setup mode or the AOSS™ mode enabled. Make sure that only one access point/router has the SecureEasySetup™ mode, Wi-Fi Protected Setup mode or the AOSS™ mode enabled and try starting from c again. LED indications when using the one-push wireless setting mode LEDs Back Cover Toner (Yellow) Drum (Yellow) Paper (Yellow) Status (Red / Green) Setting WLAN 1 Connecting Connected 2 SES/WPS/ AOSS 1 Connection Fail 3 No Access Point 3 1 The LED will blink (turn on for 0.2 seconds and off for 0.1 second). 2 The LED will turn on for 5 minutes. 3 The LED will blink (turn on for 0.1 second and off for 0.1 second) for 30 seconds. 4 The LED will flash 10 times and then turn OFF for half a second. This pattern will repeat 20 times. 6 Connection Error 4 You have completed the wireless setup. To install the printer driver, Go to step a on page 93 for Windows® or page 97 for Macintosh. 92

Section	Page
NETWORK USER'S GUIDE	1
Table of Contents	6
1 Introduction	11
Overview	11
Network features	12
Network printing	12
Management utilities	12
Types of network connections	14
Network connection example	14
Peer-to-Peer printing using TCP/IP	14
Network Shared printing	15
Wireless network connection examples (For HL-5370DW)	16
Connected to a computer with an access point on the network (Infrastructure mode)	16
Connected to a wireless capable computer without an access point on the network (Ad-hoc mode)	16
Protocols	17
TCP/IP protocols and functions	17
DHCP/BOOTP/RARP	17
APIPA	17
ARP	17
DNS client	17
NetBIOS name resolution	17
WINS	18
LPR/LPD	18
SMTP client	18
Custom Raw Port (default is Port9100)	18
IPP	18
mDNS	18
Telnet	18
SNMP	18
LLMNR	18
Web services	19
Web server (HTTP)	19
IPv6	19
Other Protocol	19
LLTD	19
2 Configuring your machine for a network	20
Overview	20
IP addresses, subnet masks and gateways	20
IP address	20
How the IP address is assigned to your print server:	20
Subnet mask	21
Gateway (and router)	21
Step by step chart	22
Setting the IP address and subnet mask	23
Using the BRAdmin Light utility to configure your machine as a network printer	23
BRAdmin Light	23
How to configure your machine using the BRAdmin Light utility	23
Using the control panel to configure your machine for a network (For HL-5380DN)	25
Using other methods to configure your machine for a network	25
Changing the print server settings	26
Using the BRAdmin Light utility to change the print server settings	26
Using the BRAdmin Professional 3 utility to change the print server settings (For Windows®)	26
Using Web Based Management (web browser) to change the print server settings	27
Using the control panel to change the print server settings (For HL-5380DN)	27
Using other methods to change print server settings	27
3 Configuring your machine for a wireless network (For HL-5370DW)	28
Overview	28
Wireless network terms and concepts	29
SSID (Service Set Identifier) and channels	29
SSID	29
Channels	29
Authentication and encryption	29
Authentication methods	29
Encryption methods	30
Network Key	31
Step by step chart for wireless network configuration	32
For Infrastructure mode	32
For Ad-hoc mode	33
Confirm your network environment	34
Connected to a computer with an access point in the network (Infrastructure mode)	34
Connected to a wireless capable computer without an access point in the network (Ad-hoc mode)	34
Confirm your wireless network setup method	35
Configuration using the Brother installer application on the CD-ROM to configure your machine for a wireless network (Recommended)	35
Configuration temporarily using a network cable	35
Configuration using the one-push wireless setting mode to configure your machine for a wireless network (Infrastructure mode only)	36
Configuration using the PIN Method of Wi-Fi Protected Setup to configure your machine for a wireless network (Infrastructure mode only)	37
Configure your machine for a wireless network	38
Using the Brother installer application on the CD-ROM to configure your machine for a wireless network (Recommended)	38
Using the one-push wireless setting mode to configure your machine for a wireless network	38
Using the PIN Method of Wi-Fi Protected Setup to configure your machine for a wireless network	38
4 Wireless configuration for Windows® using the Brother automatic installer application (For HL-5370DW)	39
Configuration in Infrastructure mode	39
Before configuring the wireless settings	39
Configure the wireless settings	41
Configuration using the automatic wireless (one-push) method	50
Before configuring the wireless settings	50
Configure the wireless settings	51
Configuration in Ad-hoc mode	56
Before configuring the wireless settings	56
Configure the wireless settings	57
Installing the printer driver	68
5 Wireless Configuration for Macintosh using the Brother installer application (For HL-5370DW)	71
Configuration in Infrastructure mode	71
Before configuring the wireless settings	71
Configure the wireless settings	73
Configuration using the automatic wireless (one-push) method	81
Before configuring the wireless settings	81
Configure the wireless settings	82
Configuration in Ad-hoc mode	87
Before configuring the wireless settings	87
Configure the wireless settings	88
Installing the printer driver	98
6 Wireless configuration using the one-push wireless setting mode (For HL-5370DW)	100
Overview	100
How to configure your wireless machine, using the one-push wireless setting mode	101
For Windows® users	103
For Macintosh users	107
7 Wireless configuration using the PIN Method of Wi-Fi Protected Setup (For HL-5370DW)	110
Overview	110
How to configure your wireless machine, using the PIN Method of Wi-Fi Protected Setup	110
For Windows® users	113
For Macintosh users	117
8 Control panel features	120
Overview	120
NETWORK menu (For HL-5380DN)	121
TCP/IP	121
BOOT METHOD	121
IP ADDRESS	122
SUBNET MASK	123
GATEWAY	123
IP BOOT TRIES	124
APIPA	124
IPV6	125
ETHERNET	125
FACTORY RESET	126
Printing the Printer Settings Page	127
Reset the network settings to the factory default	128
Enabling or disabling the wireless network (For HL-5370DW)	129
9 Driver Deployment Wizard (Windows® only)	130
Overview	130
Connection methods	130
Peer-to-peer	130
Network Shared	131
Local Printer (USB or parallel)	131
How to install the Driver Deployment Wizard software	132
Using the Driver Deployment Wizard software	133
10 Web Based Management	136
Overview	136
How to configure the machine settings using Web Based Management (web browser)	137
11 Network printing from Windows® basic TCP/IP Peer-to-Peer printing	139
Overview	139
Configuring the standard TCP/IP port	140
Printer driver not yet installed	140
For Windows Vista® and Windows Server® 2008	140
For Windows® 2000/XP and Windows Server® 2003	141
Printer driver already installed	142
Other sources of information	142
12 Internet printing for Windows®	143
Overview	143
IPP printing for Windows® 2000/XP, Windows Vista® and Windows Server® 2003/2008	143
For Windows Vista® and Windows Server® 2008	143
For Windows® 2000/XP and Windows Server® 2003	145
Specifying a different URL	147
Other sources of information	147
13 Network printing from Macintosh using the BR-Script 3 driver	148
Overview	148
How to choose the printer driver (TCP/IP)	148
14 Security features	152
Overview	152
Security terms	152
Security protocols	153
Security methods for E-mail notification	153
Configuring the protocol settings	154
Managing your network printer securely	155
Secure Management using Web Based Management (web browser)	155
Secure Management using BRAdmin Professional 3 (for Windows®)	158
Printing documents securely using IPPS	159
Specifying a different URL	159
Using E-mail notification with user authentication	160
Creating and installing a certificate	162
Creating and installing a self-signed certificate	164
How to create and install a self-signed certificate	164
How to install the self-signed certificate on your computer	165
Creating CSR and installing a certificate	177
How to create the CSR	177
How to install the certificate to your printer	177
Import and export the certificate and private key	178
How to import the certificate and private key	178
How to export the certificate and private key	178
15 Troubleshooting	179
Overview	179
General problems	179
Network print software installation problems	181
Printing problems	184
Protocol-specific troubleshooting	185
Windows® 2000/XP, Windows Vista® and Windows Server® 2003/2008 IPP troubleshooting	185
Web Based Management (web browser) troubleshooting (TCP/IP)	185
Wireless network troubleshooting (For HL-5370DW)	186
Wireless setup problems	186
Wireless connection problem	187
A Appendix	188
Using services	188
Other ways to set the IP address (For advanced users and administrators)	188
Using DHCP to configure the IP address	188
Using BOOTP to configure the IP address	189
Using RARP to configure the IP address	190
Using APIPA to configure the IP address	190
Using ARP to configure the IP address	191
Using the TELNET console to configure the IP address	192
Using the Brother Web BRAdmin server software for IIS to configure the IP address	193
Installation when using a Network Print Queue or Share	194
Installation when using Web Services (For Windows Vista® users)	195
B Appendix	196
Print server specifications	196
Ethernet wired network	196
Wireless network (for HL-5370DW)	197
Function table and factory default settings (For HL-5380DN)	198
C Appendix	199
Open Source Licensing Remarks	199
OpenSSL statements	199
OpenSSL License	199
Original SSLeay License	200
Part of the software embedded in this product is gSOAP software.	201
This product includes SNMP software from WestHawk Ltd.	201

Match case Limit results 1 per page

Wireless configuration using the one-push wireless setting mode (For HL-5370DW)

Wait until the

Status

LED of your machine indicates

Connected

. The

Status

LED will turn on for 5

minutes. (See the table below) This indication means the machine has successfully connected to your

access point/router. You can now use your machine in a wireless network.

If the LED indicates

Connection Fail

(See the table below), the machine has not successfully

connected to your access point/router. Try starting from

again. If the same message is indicated

again, reset the print server back to its factory default settings and try again. For resetting, see

Reset the

network settings to the factory default

on page 118.

If the LED indicates

No Access Point

(See the table below), the machine has detected no access

point/router on your network. Make sure you place the Brother machine as close to the network access

point/router as possible with minimal obstructions, and try starting from

again. If the same message

is indicated again, reset the print server back to its factory default settings and try again. For resetting,

see

Reset the network settings to the factory default

on page 118.

If the LED indicates

Connection Error

(See the table below), the machine has detected more than

2 access points/routers on your network that have the SecureEasySetup™, the Wi-Fi Protected Setup

mode or the AOSS™ mode enabled. Make sure that only one access point/router has the

SecureEasySetup™ mode, Wi-Fi Protected Setup mode or the AOSS™ mode enabled and try starting

from

again.

LED indications when using the one-push wireless setting mode

The LED will blink (turn on for 0.2 seconds and off for 0.1 second).

The LED will turn on for 5 minutes.

The LED will blink (turn on for 0.1 second and off for 0.1 second) for 30 seconds.

The LED will flash 10 times and then turn OFF for half a second. This pattern will repeat 20 times.

You have completed the wireless setup. To install the printer driver, Go to step

on page 93

for Windows

or page 97 for Macintosh.

LEDs

Setting

WLAN

Connecting

SES/WPS/

AOSS

Connected

Connection

Fail

No Access

Point

Connection Error

Back

Cover

Toner

(Yellow)

Drum

(Yellow)

Paper

(Yellow)

Status

(Red /

Green)