Brother International HL-660 Users Manual - English - Page 60

User Printer TrueType™ Fonts, Graphics Mode

Get Brother International HL-660 - B/W Laser Printer PDF manuals and user guides View all Brother International HL-660 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

English USER'S GUIDE For errors shown below, the printer indicates an operator call by blinking the ALARM lamp and printing the error messages on paper. Error Memory Full Print Overrun Centronics Interface Line Error Action • Press the FF/CONT switch to print the data remaining in the printer. • If you are using the supplied Windows driver, try again after changing the following settings. The best combination of the settings below varies depending on your document. Graphics Mode TrueType mode User Printer TrueType™ Fonts Page Protection • Expand the printer memory by adding a commercially available SIMM. • Reduce the print resolution or reduce the complexity of your document. • Press the FF/CONT switch to print the data remaining in the printer. • If you use the supplied Windows driver, try again after changing the following settings. The best combination of the settings below varies depending on your document. Graphics Mode TrueType mode User Printer TrueType™ Fonts Page Protection • If this does not clear the error, reduce the complexity of your document or reduce the print resolution. • Expand the printer memory by installing SIMM and set page protection ON by using the supplied Windows driver or RPC program. • Press the FF/CONT switch to resume printing. • Check that the connection between your computer and printer is secure and correct, and check the interface cable.  Note If the printer does not operate as you expect it to, it is recommended that you perform a user reset or factory reset with the switches or unplug the printer, wait a few seconds and then plug it in again. If you still have problems, consult your dealer or our authorized service representative. 6-2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
USER’S GUIDE
6–2
English
For errors shown below, the printer indicates an operator call by blinking
the ALARM lamp and printing the error messages on paper.
Error
Action
Memory Full
•
Press the FF/CONT switch to print the data
remaining in the printer.
•
If you are using the supplied Windows driver, try
again after changing the following settings.
The
best combination of the settings below varies
depending on your document.
Graphics Mode
TrueType mode
User Printer TrueType™ Fonts
Page Protection
•
Expand the printer memory by adding a
commercially available SIMM.
•
Reduce the print resolution or reduce the complexity
of your document.
Print Overrun
•
Press the FF/CONT switch to print the data
remaining in the printer.
•
If you use the supplied Windows driver, try again
after changing the following settings.
The best
combination of the settings below varies depending
on your document.
Graphics Mode
TrueType mode
User Printer TrueType™ Fonts
Page Protection
•
If this does not clear the error, reduce the
complexity of your document or reduce the print
resolution.
•
Expand the printer memory by installing SIMM and
set page protection ON by using the supplied
Windows driver or RPC program.
Centronics
Interface Line
Error
•
Press the FF/CONT switch to resume printing.
•
Check that the connection between your computer
and printer is secure and correct, and check the
interface cable.
Note
If the printer does not operate as you expect it to, it is recommended that
you perform a user reset or factory reset with the switches or unplug the
printer, wait a few seconds and then plug it in again. If you still have
problems, consult your dealer or our authorized service representative.