Brother International HL-660 Users Manual - English - Page 65

Q & A, Setting up the Printer Hardware

Get Brother International HL-660 - B/W Laser Printer PDF manuals and user guides View all Brother International HL-660 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

English CHAPTER 6 TROUBLESHOOTING Q & A This section contains questions and answers for using your printer. If you have encountered a problem, find the question relating to your problem and take the steps recommended to correct the problem. Setting up the Printer Hardware Question The printer does not work. All lamps are off. The printer does not print. Recommendation The printer may be in sleep mode. Press any switch to wake up printer. Check the following: • The protective parts have been removed. • The toner cartridge and drum unit are installed properly. • The interface cable is securely connected between the printer and computer. • Check to see if any lamps are blinking. Notice which lamps are blinking and refer to Operator Call section of this manual. Setting up the Printer for DOS Questions I cannot print from my application software Recommendation • Check if the DOS application software interface settings match that of your printer. ( i.e., if you are using a parallel printer cable, then you would most likely set your DOS software printer port to LPT1.) • Check to see if the printer has any printer alarms active. 6-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
CHAPTER 6 TROUBLESHOOTING
6–7
English
Q & A
This section contains questions and answers for using your printer. If you
have encountered a problem, find the question relating to your problem
and take the steps recommended to correct the problem.
Setting up the Printer Hardware
Question
Recommendation
The printer does not
work. All lamps are off.
The printer may be in sleep mode. Press any
switch to wake up printer.
The printer does not print.
Check the following:
•
The protective parts have been removed.
•
The toner cartridge and drum unit are
installed properly.
•
The interface cable is securely connected
between the printer and computer.
•
Check to see if any lamps are blinking.
Notice which lamps are blinking and refer
to Operator Call section of this manual.
Setting up the Printer for DOS
Questions
Recommendation
I cannot print from my
application software
•
Check if the DOS application software
interface settings match that of your printer.
( i.e., if you are using a parallel printer
cable, then you would most likely set your
DOS software printer port to LPT1.)
•
Check to see if the printer has any printer
alarms active.