Brother International Innov-is 80 Operation Manual - Page 38

Pulling up the bobbin thread

Get Brother International Innov-is 80 PDF manuals and user guides View all Brother International Innov-is 80 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

GETTING READY Pulling up the bobbin thread When making gathers or before free-motion quilting, first pull up the bobbin thread as described below. Insert the bobbin into the bobbin case. a • Refer to steps a through e of "Installing the bobbin" (page 26). Pass the bobbin thread through the slot. b Do not cut the thread with the cutter. Turn on the sewing machine. c While lightly holding the upper thread with d your left hand with the needle in the up- position, press (needle position button) twice to lower and raise the needle. Pull out about 10 cm (4 inches) of the bobbin f thread under the presser foot toward the rear of the machine. Turn off the sewing machine. g Reattach the bobbin cover. h Insert the tab in the lower-left corner of the bobbin cover (A), and then lightly press down on the right side (B). B A 1 a Needle position button X The bobbin thread is looped around the upper thread and can be pulled up. Carefully pull the upper thread upward to pull e out the end of the bobbin thread. 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
GETTING READY
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
36
Pulling up the bobbin thread
When making gathers or before free-motion quilting,
first pull up the bobbin thread as described below.
a
Insert the bobbin into the bobbin case.
• Refer to steps
a
through
e
of “Installing the
bobbin” (page 26).
b
Pass the bobbin thread through the slot.
Do not cut the thread with the cutter.
c
Turn on the sewing machine.
d
While lightly holding the upper thread with
your left hand with the needle in the up-
position, press
(needle position button)
twice to lower and raise the needle.
a
Needle position button
X
The bobbin thread is looped around the
upper thread and can be pulled up.
e
Carefully pull the upper thread upward to pull
out the end of the bobbin thread.
f
Pull out about 10 cm (4 inches) of the bobbin
thread under the presser foot toward the rear
of the machine.
g
Turn off the sewing machine.
h
Reattach the bobbin cover.
Insert the tab in the lower-left corner of the
bobbin cover (A), and then lightly press down
on the right side (B).
1
A
B