Brother International TD-2135NWB Users Guide TD-2020A/2125NWB/2135NWB - Page 16

Cutting Roll Paper

Get Brother International TD-2135NWB PDF manuals and user guides View all Brother International TD-2135NWB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

Chapter 2 Figure 1 Figure 3 2 2 1 NOTE This is the sensor's default position. Figure 2 2 2 3 4 5 1 Back of media 2 Black mark 3 0.16" (4 mm) or more 4 Centerline 5 Reflective/black mark sensor NOTE When using receipt paper with the maximum width of 2.4" (63 mm), make a black mark at least 0.35" (9 mm) long in from either the left or right edge of the paper so that the reflective/black mark sensor can detect the black mark. If the black mark is too short, it cannot be detected by the reflective/black mark sensor. Cutting Roll Paper 2 Roll paper can be cut using the printer's tear bar. Pull one edge of the ejected paper up and diagonally toward the other edge. CAUTION The tear bar is sharp. To avoid injury, do not touch the tear bar. 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
Chapter 2
10
Figure 1
2
NOTE
This is the sensor's default position.
Figure 2
2
Figure 3
2
1
Back of media
2
Black mark
3
0.16" (4 mm) or more
4
Centerline
5
Reflective/black mark sensor
NOTE
When using receipt paper with the
maximum width of 2.4" (63 mm), make
a black mark at least 0.35" (9 mm) long
in from either the left or right edge of the
paper so that the reflective/black mark
sensor can detect the black mark. If the
black mark is too short, it cannot be
detected by the reflective/black mark
sensor.
Cutting Roll Paper
2
Roll paper can be cut using the printer’s tear
bar. Pull one edge of the ejected paper up
and diagonally toward the other edge.
CAUTION
The tear bar is sharp. To avoid injury, do not
touch the tear bar.
1
2
3
4
5