Brother International andtrade; QL-1060N Quick Setup Guide - English and Spani - Page 15

Connecting the Power Supply

Get Brother International andtrade; QL-1060N PDF manuals and user guides View all Brother International andtrade; QL-1060N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 15 highlights

9 Introduction 3 Thread the end of the DK Roll into the slot until it can be seen from the other side. When unable to thread the end of the DK Roll into the slot, thread it as far as possible, and then close the cover. Press the ON/OFF button to turn the QL-1060N on, and then press the STEP 1 FEED button to set the roll. 4 Close the DK Roll compartment cover until it clicks right and left side. Getting started STEP 2 Installing the Software For Macintosh® For Windows® 4 Connecting the Power Supply Connect the power cord to the QL-1060N and then plug the power cord into a electrical outlet. STEP 3 • Check that the electrical outlet is 120V AC before plugging the power cord. Label Overview • Unplug the power cord from the electrical outlet after you have finished using the QL-1060N. • Do not pull the power cord when unplugging it from the electrical outlet. The wire in the power cord may become damaged. • Do not connect the QL-1060N to the computer until directed to do so when installing the printer driver. STEP 4 Reference

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
9
STEP
1
STEP
2
STEP
3
For Windows
®
For Macintosh
®
STEP
4
Getting started
Reference
Installing the Software
Label Overview
Introduction
Connect the power cord to the
QL-1060N and then plug the power
cord into a electrical outlet.
•
Check that the electrical outlet is 120V
AC before plugging the power cord.
•
Unplug the power cord from the
electrical outlet after you have finished
using the QL-1060N.
•
Do not pull the power cord when
unplugging it from the electrical outlet.
The wire in the power cord may
become damaged.
•
Do not connect the QL-1060N to the
computer until directed to do so when
installing the printer driver.
3
Thread the end of the DK Roll into
the slot until it can be seen from the
other side.
When unable to thread the end of the
DK Roll into the slot, thread it as far as
possible, and then close the cover.
Press the ON/OFF button to turn the
QL-1060N on, and then press the
FEED button to set the roll.
4
Close the DK Roll compartment cover until it
clicks right and left side.
4
Connecting the Power Supply