Campbell Scientific CS616 CS616 and CS625 Water Content Reflectometers - Page 28

Sensor lead, AM16/32, CR10X

Get Campbell Scientific CS616 PDF manuals and user guides View all Campbell Scientific CS616 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

CS616 and CS625 Water Content Reflectometers Sensor lead CS616-1 green CS616-2 green CS616-3 green CS616-1,2,3 orange CS616-4 green CS616-5 green CS616-6 green CS616-4,5,6 orange ... CS616-46 green CS616-47 green CS616-48 green CS616-46,47,48 AM16/32 1H 1L 2H 2L 3H 3L 4H 4L ... 31H 31L 32H 32L RES CLK COM ODD H COM ODD L COM EVEN H COM EVEN L CR10X C1 C2 SE1 SE2 SE3 C3 ;{CR10X} ; *Table 1 Program 01: 60 Execution Interval (seconds) 1: Batt Voltage (P10) ;Measure battery voltage 1: 1 Loc [ Bat_Volt ] 2: Internal Temperature (P17) ;Measure datalogger internal temperature 1: 2 Loc [ DL_Temp ] 3: If time is (P92) ;Every 60 Minutes Start Multiplexer Measurement Loop 1: 0 Minutes (Seconds --) into a 2: 60 Interval (same units as above) 3: 11 Set Flag 1 High 4: If Flag/Port (P91) ;User can start Measurement Loop by setting Flag 1 High 1: 11 Do if Flag 1 is High 2: 30 Then Do 5: Do (P86) 1: 41 ;Set control port 1 high (i.e. Reset Multiplexer) Set Port 1 High 6: Beginning of Loop (P87) 1: 0 Delay 2: 16 Loop Count ;16 loops X 3ea CS616 measured/loop 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
CS616 and CS625 Water Content Reflectometers
Sensor lead
AM16/32
CR10X
CS616-1 green
1H
CS616-2 green
1L
CS616-3 green
2H
CS616-1,2,3 orange
2L
CS616-4 green
3H
CS616-5 green
3L
CS616-6 green
4H
CS616-4,5,6 orange
4L
...
…
CS616-46 green
31H
CS616-47 green
31L
CS616-48 green
32H
CS616-46,47,48
32L
RES
C1
CLK
C2
COM ODD H
SE1
COM ODD L
SE2
COM EVEN H
SE3
COM EVEN L
C3
;{CR10X}
;
*Table 1 Program
01: 60
Execution Interval (seconds)
1:
Batt Voltage (P10)
;Measure battery voltage
1: 1
Loc [ Bat_Volt
]
2:
Internal Temperature (P17) ;Measure datalogger internal temperature
1: 2
Loc [ DL_Temp
]
3:
If time is (P92)
;Every 60 Minutes Start Multiplexer Measurement Loop
1: 0
Minutes (Seconds --) into a
2: 60
Interval (same units as above)
3: 11
Set Flag 1 High
4:
If Flag/Port (P91)
;User can start Measurement Loop by setting Flag 1 High
1: 11
Do if Flag 1 is High
2: 30
Then Do
5:
Do (P86)
;Set control port 1 high (i.e. Reset Multiplexer)
1: 41
Set Port 1 High
6:
Beginning of Loop (P87)
;16 loops X 3ea CS616 measured/loop
1: 0
Delay
2: 16
Loop Count
22