Canon LV-7375 Projector Monitoring Software Ver.1.0.0 User's Manual
Canon LV-7375 Manual
View all Canon LV-7375 manuals
Add to My Manuals
Save this manual to your list of manuals |
Canon LV-7375 manual content summary:
- Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 1
Projector Monitoring Software Ver. 1.0.0 User's Manual - Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 2
to as "this software") is a software that uniformly manages network-connected compliant Canon Projectors, via network. Operating conditions and maintenance information of up to 253 projectors can be monitored and managed. This manual describes the introduction of this software, and its routine - Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 3
for management to the network, and configure its network settings. In addition, you must configure the SNMP settings of the projector when using SNMP protocol. For procedures on configuring the projector, see the instruction manual that came with the projector. 3 Installing the Software ▼ Install - Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 4
Supported Languages Japanese, English CPU Intel Pentium 4 2.4 GHz or better Memory 1 GB or more Display XGA . 22 Follow the instructions provided by the installer allow communication with the projector. Click [OK] if this software, click the Windows [Start] menu, select [Control Panel], and [Add - Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 5
Discovery Settings Configure the network range for discovering projectors. Methods vary depending on "SNMP V1/V2c/V3" and "LV Series". Configure each SNMP V3 is used in this example. 11 From [Discovery settings] of the [Option] menu, select a name of protocol ([SNMP V1] / [SNMP V2c] / [SNMP V3]) - Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 6
33 To configure a broadcast address, select the [Broadcast] tab and click the [New] button. [Specify broadcast discovery settings] dialog will display. Note -- As default, broadcast settings configured on the network card of the administrative computer will display in the discovery range list. 44 - Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 7
CHAPTER 1 • Introduction 66 Complete the dialog with necessary information and click the [OK] button. Category First address Last address Community name Timeout Password (SNMP V3 only) Enable encryption (SNMP V3 only) Description Enter a first IP address in the range for discovery, in "XXX. XXX. - Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 8
projector's IP address changes. Configure LV series with the following procedures. 11 From [Discovery setting] of the [Option] menu, select [LV series] to configure. [Discovery settings] dialog will display. 22 Place a checkmark in [Enable LV series]. Remove a - Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 9
44 Complete the dialog with necessary information and click the [OK] button. Category IP address Port number Timeout Description Enter an IP address of the projector, in "XXX.XXX.XXX.XXX" form. Enter a port number to be used, in one-byte numbers. Default value is set to "7142." Enter a number of - Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 10
interval from "1 hour/2 hour/3 hour/6 hour/12 hour/24 hour/Not specified", for discovering new projectors. If "Not specified" is chosen, poll manually with [Discover projector] from the [View] menu. Note -- Settings will be cancelled if [X] (Close) or [Cancel] button is clicked before clicking - Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 11
will display. 2222 Exiting the Software Exit this software with the following procedures. 11 Select [Exit] from the [Group] menu. Informations of projectors and groups are saved and the software will exit. Note -- You can also exit the software by clicking the [X] (close) button on the window - Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 12
operating procedures, see referring pages for details. Menu bar Projector list (see p. 17) Projector group list (see p. 13) Status bar Name Menu bar Projector group list Projector list Status bar 12 Description Displays the function menu. Displays projector groups. Select a group from the list - Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 13
lamps, see the instruction manual that came with the projector. Group that automatically classifies all managed projectors depending on its status. Status groups can be created by specifying the location or status. You can change or delete the parameters of this Status group. (e.g. "Clean Filter - Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 14
a new lamp", "Replace with the new lamp", "Obtain or replace with the new lamp", or "Warning". Select from "over" or "less than", and enter a number from 0 to 99999 for lamp usage time. Select a status of the filter from "Normal", "Cleaning the air filter", "Replacing the air filter" or "Cleaning or - Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 15
must create a new projector group with conditions entered in necessary parameter categories. Change the projector group settings with the following procedures. 11 Select a projector group to change from the Projector group list, and select [Edit] from the [Group] menu. [Edit projector group] dialog - Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 16
created by the user can be deleted. Note -- You can not delete the "Typical group." Delete a projector group with the following procedures. 11 Select a projector group to delete from the Projector group list, and select [Delete] from the [Group] menu. 22 Confirm the dialog and click [Yes]. Selected - Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 17
to confirm the properties from the Projector list, and select [Projector information] from the [Projector] menu. Properties dialog of the selected projector will display. Projector name, location, status, lamp replacement, air filter cleaning and replacement information are displayed in the - Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 18
contact numbers and maintenance records in projectors with the following procedures. 11 Select a projector to confirm the properties from the Projector list, and select [Projector information] from the [Projector] menu. Properties dialog of the selected projector will display. 22 Click the comment - Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 19
[Projector] menu. Browser will run and display the web settings dialog of the projector. Note -- For procedures on using the web settings dialog, see the instruction manual that came with the projector. 222222 Setting the Projector List All compatible projectors once recognized within the network - Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 20
copy to the specified User group. 222222 Discovering Projectors Discover new connected projectors manually with the following procedures. 11 Select [Discover projectors] from the [View] menu. New projectors will be discovered on the network and displayed in the Projector list. Note -- To cancel the - Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 21
changed. In this case, adjust the protocol settings of the projector labelled "disconnected" in accordance with the changed network settings, with the following procedures. 11 Select [Protocol settings] from the [Projector] menu. "Protocol settings" dialog will appear. 22 Select a protocol from the - Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 22
•• Make sure that the projector's [Network Function] is turned "On". •• Confirm the IP address and/or network settings. •• Configure the SNMP settings of the projector if the projector is SNMP-compatible. See the instruction manual that came with the projector for SNMP configuration procedures. 22 - Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 23
this software can communicate with the projector. See the instruction manual of the software for configuration procedures. ■■ Projector classified into "Warning" Cause Solution Projector is encountering trouble •• For projectors classified into "Warning" of the Projector group list, confirm its - Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 24
. Also, this software will not display [Faulty Lamp] and [Faulty Power Supply] when they occur with the projector. (August 2009) 3333 LV Series Projectors Usage Precaution Names of [Input] display differently between this software and the projector. Refer to the chart below for corresponding input - Canon LV-7375 | Projector Monitoring Software Ver.1.0.0 User's Manual - Page 25
YT1-1419-000 © CANON INC. 2009
Projector Monitoring Software
Ver. 1.0.0
User’s Manual